Quick Facts DISH 1000.2 - First Strike Meters

TMQuick Facts DISH 1000.2HIGHLIGHTS• Receives signal from the 110°,119° and 129° orbital locations.• Antenna reflector size is slightlylarger than a DISH 1000.• Standard installation uses DISHPro Plus 1000.2 LNBF andIntegrated Adapter Bracket.− Three receiver output ports.− One LNB input port for afourth orbital location.− Compatible with DISH Prosingle-orbital LNBFs or DISHNetwork bandstacked LNBFs,and DISH Pro Plus 44 switch.• Optional installation: three Dual(or Single) LNBFs with Three-LNBF Bracket and a switch.DISH 1000.2 withDP Plus 1000.2 LNBFPART NUMBERS• Antenna assembly Kit #143897 –includes reflector, mast/foot,backing structure and IntegratedAdapter Bracket (for DPP 1000.2LNBF)• DPP 1000.2 LNBF #145511• Three-LNBF Bracket #151239(10-pack)• 10-packs also available forreflector, mast/foot, andbacking structureDESCRIPTIONThe DISH 1000.2 receives signalfrom the 110°, 119° and 129° DBSorbital locations. The DISH Pro Plus1000.2 LNBF supports threereceivers and includes an LNBFinput port for a fourth orbitallocation.DPP 1000.2 LNBF FEATURES• Supports connection of up tothree satellite receivers in anycombination*:− Single-cable connection toDISH Pro Plus¹ (dual-tuner)receivers, when each is usedwith a DP Plus Separator.− Single-cable connection toDISH Pro receivers.− Single-cable connection toLegacy receivers², without aDISH Pro Adapter.− Supports a two-cableconnection to one DISH ProPlus (dual-tuner) receiver,when not used with a DPPlus Separator.*Note: Legacy receivers mustbe connected with at least onepowered DISH Pro or DISH ProPlus receiver.DPP 1000 .2 LNBF FEATURES,continued• Includes an LNB input port forconnection of a second dish toreceive signal from a fourthorbital location. Connectedreceiver(s) receive signal fromall four orbital locations²,eliminating the need for anexternal switch.TWO LNBF BRACKETS AVAILABLE• The “Integrated AdapterBracket” is used only with theDISH 1000.2 LNBF.• The “Three-LNBF Bracket” isused only with Dual and/orSingle LNBFs.− Use all DISH Pro or all LegacyLNBFs with a matching switch.− You cannot use a Twin/QuadLNBF with this bracket.− This is not the same as theW-Bracket used with the DISH1000.¹DISH Pro Plus (dual-tuner) receivers include:DISH 322, DISH Player-DVR 522 & 625, DISH 721,DISH Player-DVR 921, DISH Player-DVR 942,ViP622 DVR, future dual-tuner receivers andequivalent JVC and RCA models.² Models 1000, 2000, 3000, 4000, 5000, JVC-DVHS and DishPlayer 7100/7200 may not detectand will not support 129°; these receiverscannot view the fourth orbital location (ifconnected).Comparison of DISH 1000.2 to DISH 1000DISH 1000.2 DISH 1000Orbital Locations 110°, 119°, 129° 110°, 119°, 129°# of Receiverssupportedwithout a switchLNBF Comparison(StandardConfiguration)ThreeDPP 1000.2 integratedLNBF (LNB In port foroptional fourth orbitallocation)TwoDPP Twin with DP Dual(LNB In port on DPP Twinused for DP Dualproviding 129°)Height 20.7” 18”Width 25.9” 22.8”MastOutside diameter: 1.66”Slightly longer than DISH1000Outside diameter: 1.66”Contents subject to change without notice. Rev. 12/14/06EchoStar Technologies CorporationPage 1 of 2

TMQuick Facts DISH 1000.2INSTALLATION CONSIDERATIONS• Mounting and installationrequirements are similar to DISH1000.• Additional skew holes areprovided on the bracket forextreme skew angles (greaterthan 110 or less than 70).• DISH Pro (DP) and DISH Pro Plus(DPP) receivers can be no morethan 200 feet from the furthestLNBF.• Legacy receivers can be no morethan 100 feet away from the DISH1000.2.• Only a DISH Pro Plus 44 Switchcan be used with the DP Plus1000.2 LNBF.• The DP Plus 1000.2 LNBF is notcompatible with Legacy LNBFs orswitches.• The DP Plus 1000.2 LNBF’sdefault orbital locations are 119°on PORT 1, 110° on PORT 2, and129° on PORT 3, similar to otherLNBFs. Use port 1 for peaking.• As with all DISH Pro Plusinstallations, cable andcomponents between the LNBFs,switches, DP Plus Separator andreceivers must be rated to atleast 2150 MHz and pass DiSEqC.Refer to the DISH NetworkApproved Accessories List.LNBF/SWITCH CONFIGURATIONSConnect a Fourth OrbitalLocation to the DP Plus 1000.2LNBF:• The LNBF includes an input port(labeled LNB IN) for anadditional orbital location.• Accepts signal from a DP Singleor DP Dual LNBF, or a DISHNetwork bandstacked LNB.• The fourth orbital location dishmust be within 80 feet of theDP Plus 1000.2 LNBF, and within200 feet of the DP or DPPreceiver.• The LNB input is operationalonly when the LNBF isconnected directly to satellitereceivers. It is disabled whenthe LNBF is connected to aswitch.Add Additional Receivers:• Connect the three output portsof the DP Plus 1000.2 LNBF to aDPP44 switch for a fourthreceiver. When connected to aDPP44 switch using threecables, the LNBF provides signalfrom 110°, 119° and 129°.Three-LNBF Bracket:• For installations with threeDual (or Single) LNBFs. Use anycompatible switch.• This is a new bracket that isnot compatible with DISH 1000,or with Twin/Quad LNBFs.• The center LNBF (119°) is usedfor peaking.FOR MORE INFORMATION• DISH 1000.2 Installation Guide• DISH 1000.2 Product LaunchBulletin129°119°110°Three- LNBF BracketContents subject to change without notice. Rev. 12/14/06EchoStar Technologies CorporationPage 2 of 2