Temel Tanımlar - Gebze Yüksek Teknoloji Enstitüsü

ME 612Metal Forming and Theory of PlasticityYrd.Doç.Dr. Ahmet Zafer Şenalpe‐mail: azsenalp@gyte.edu.trMakine Mühendisliği BölümüGebze Yüksek Teknoloji Enstitüsü

ME 612Metal Forming and Theory of PlasticityReferences[1] Johnson, W. and Mellor, P.B., Engineering Plasticity, New York Van Nostrand Reinhold.[2] Hosford, W.F. and Caddell R.M., Metal Forming Mechanics and Metallurgy , Prentice Hall International Editions.[3] Johnson, W., Upper Bound Loads for Extrusion Through Circular Shaped Dies , Appl. Sci. Res. Series A, Vol. 7, p. 437, 1958.[4] Liu, J.Y., Upper Bound Solutions of Some Axisymmetric Cold Forging Problems, Transactions of the ASME, Journal ofEngineering for Industry, pp. 1134‐1144, November, 1971.[5] Nagpal, V., Lahoti, G.D. and Altan, T., A Numerical Method for Simultaneous Prediction of Metal Flow and Temperatures inUpset Forging of Rings, Transactions of the ASME, Journal of Engineering for Industry, November, Vol. 100, pp. 413‐420,1978.[6] Avitzur, B., An Upper Bound Approach to Cold Strip Rolling', Journal Engineering Industry, ASME, Paper No: 63 Prod. 8.[7] Hosford, W.F. and Caddell, R.M., Metal Forming Mechanics and Metallurgy, Prentice Hall International Editions, pp. 115‐ 138,1983.[8] Akgerman, N. and Altan, T., Modular Analysis of Geometry and Stresses in Closed Die Forging: Application to a Structural Part,Transactions of the ASME, Journal of Engineering for Industry, November, PP.1025 1034, 1972.[9] Hosford, W.F. and Caddell, R.M., Metal Forming Mechanics and Metallurgy, Prentice Hall International Editions, pp. 168‐ 201,1983.[10] Johnson, W., Sowerby, R. and Haddow, J.B., Plane Strain 132ip Line Fields: Theory and Bibliography, New York, AmericanElsevier, 1970.[11] Boor, F., Modelling of deep drawing of complex shaped components using slip line methods, Proceedings of 30 th InternationalMATADOR Conference, UMIST, Manchester, McMillian Ltd., pp. 217‐225. 1993.Dr. Ahmet Zafer ŞenalpME 612GYTE-Makine Mühendisliği Bölümü3

[12] Boor, F. and Kardos, K., Stress line methods for industry and education , 7 th International Machine Design and ProductionConference, September, METU, Ankara, Turkey pp. 313‐321, 1996.[13] Ghali, A. and Neville, A.M., Structural Analysis, A Unified Classical and Matrix Approach, Chapman and Hall, pp. 435‐ 471,1986.[14] Takezona, S. and Tao, K., Elasto/Visco‐Plastic Dynamic Response of General Thin Shells to Blast Loads, Bulletin of the JSME,Vol. 25, No. 203, May, pp. 728‐735, 1982.[15] Şenalp, A.Z., Computer Aided Wrinkling Analysis Of Nonsymmetric Parts In Sheet Metal Forming, Ph. D. Thesis, Middle EastTechnical University, 1998.[16] Kılkış, B. And Kaftanoğlu, B., On the Finite Diffence Formulation of Non‐Linear Plastic Deformations, Proceedings of Int. Conf.On Numerical Methods for Non‐Linear Problems, pp. 63‐73, Pineridge Press, 1980.[17] Perzyna, P., Fundamental Problems in Viscoplasticity', Advances in Applied Mechanics, Vol 9, pp 243‐377, 1966.[18] Owen, D.R.J. and Hinton, E., Finite Elements in Pllasticity Theory and Practice, Pineridge Press, Swansea, 1980.[19] Waszezyszyn, Z., Computational methods and Plasticity', Report CR 583, Tech. Univ. Delft, faculty of Aerospace, 1989.[20] Zienkiewics, O.C., Cormeau, I.C., Viscoplasticity, plasticity, and creep in elastic solids A Unified Numerical Solution Approach,Int. J. Num Meth. Engng, Vol 8, pp. 821‐845, 1974.[21] Tayal, A.K. and Natarajan, R., Extrusion of Rate Sensitive Materials Using A Viscoplastic Constitutive Equation and the FiniteElement Method, Int. J. Mech. Sci., Vol. 23, pp. 89‐98 1981.[22] Oh, S.I., Park, J.J., Kobayashi, S. and Altan, T., Application of FEM Modeling to Simulate Metal Flow in Forging a titanium AlloyEngine Dis", Transactions of the ASME, Journal of Engineering for Industry, November, Vol. 105, pp. 251‐258, 1983.[23] Chandra, A. and Mukherjee, S., A finite element analysis of metal‐forming problems with an elastic viscoplastic materialmodel. Int. Journal. Num. Meth. Eng., Vol. 20, pp. 1613‐1628, 1984.[24] Darendeliler, H., Computer Aided Deformation Analysis of Deep Drawing Process, Ph. D. Thesis, Middle East TechnicalUniversity, 1991.[25] Marcal, P.V. and King, I.P., Elastic‐Plastic Analysis of Two‐Dimensional Stress Systems by the Finite Element Method, Int. J.Mech. Sci., Vol. 9, pp. 143‐155 , 1967.[26] Prof. N. Zabaras, Materials Processing, Lecture Notes.[27] Prof. Dr. Levon Çapan, Metallerde Plastik Şekil Verme.Dr. Ahmet Zafer ŞenalpME 612GYTE-Makine Mühendisliği Bölümü4