Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...

More documents

Recommendations

Info

66 Installing and configuring VCSInstalling and configuring VCS 5.0If these checks are satisfactory, the installer lists the packages to beinstalled.7 Enter y to verify that the information up to this point is correct.Is this information correct? [y,n,q] (y)The installer performs an initial system check of the local system andchecks for installed packages on the local system. If these checks aresatisfactory, the installer program lists the packages to be installed.8 Press Enter.You may install Cluster Management Console packages without performingconfiguration. The installer program gives you the option to configureCluster Management Console now, and provides instructions forconfiguring Cluster Management Console later.9 Enter y to configure Cluster Management Console.Are you ready to configure CMC? [y,n,q] (y)10 Enter the fully-qualified management server network address, such as:Enter the network address used by the management server [?] mgmtserver1.symantec.com11 Enter y to verify that the information up to this point is correct.Is this information correct? [y,n,q] (y)12 Enter a password for the cluster connector service account.The password is the password that was entered for the cluster connectorservice account during management server installation.Enter the password for the CMC service account:xxxxx13 Enter the root hash of the authentication broker installed on themanagement server, which you can get from the Root Broker administrator.Enter the hash of the Management Server's root broker [?]■■On Windows:\program files\veritas\security\authentication\bin\vssat showbrokerhashOn UNIX systems:/opt/VRTSat/bin/vssat showbrokerhashThe output of this command looks similar to the following:Root Hash: 9dfde3d9aaebee084f8e35819c1fed7e6b01d2aeEnter the alphanumeric string (the string you receive is different from theone shown).14 Enter y to verify that the information up to this point is correct.Is this information correct? [y,n,q] (y)The installer presents:■■Installation progress percentagesAuthentication status messages
Installing and configuring VCSInstalling VCS using installonly option67■Cluster connector configuration status messages15 Enter y to start Veritas Cluster Management Console processes.Do you want to start Veritas Cluster Management Console processes now?[y,n,q] (y)The installer presents startup progress percentages and, if successful,displays the following message:Startup completed successfully on all systems16 Enter an encryption key of at least five characters.This key is used to encrypt passwords in the response file. It must bereferred to using the -enckeyfile option if the generated installationresponse file is to be used again.A string of five or more characters is required to encrypt passwords in the responsefileEnter five or more characters to be used an encryption key:xxxxxPress [Return] to continue:17 Press Enter.Record the location that the installer program provides for the installationlog files, summary file, and response file.Verifying the cluster after installationWhen you have used installvcs program and chosen to configure and start VCS,it is expected that VCS and all components are properly configured and can startcorrectly. You must verify that your cluster is operating properly after theinstallation.See “Verifying the VCS installation” on page 129.Installing VCS using installonly optionIn certain situations, users may choose to install the VCS packages on a systembefore they are ready for cluster configuration. During such situations, theinstallvcs -installonly option can be used. The installation programlicenses and installs VCS packages on the systems entered without creating anyVCS configuration files.Configuring VCS using configure optionIf you installed VCS and did not choose to configure VCS immediately, use theinstallvcs -configure option to configure VCS when you are ready for cluster
Page 1 and 2:
Veritas Cluster ServerInstallation
Page 3:
Technical supportMake sure you have
Page 6 and 7:
6 ContentsSetting up shared storage
Page 8 and 9:
8 ContentsChapter 5Setting up I/O f
Page 10 and 11:
10 ContentsChapter 8Chapter 9Adding
Page 12 and 13:
12 Contents
Page 14 and 15:
14 Introducing VCSVCS basicsFigure
Page 16 and 17: 16 Introducing VCSVCS basicsNetwork
Page 18 and 19: 18 Introducing VCSVCS basics
Page 20 and 21: 20 Preparing to install and configu
Page 46 and 47: 46 Installing and configuring VCSAb
Page 48 and 49: 48 Installing and configuring VCSIn
Page 68 and 69: 68 Installing and configuring VCSPe
Page 76 and 77: 76 Installing and configuring VCSCh
Page 82 and 83: 82 Installing and configuring VCSUn
Page 84 and 85: 84 Manually installing and configur
Page 98 and 99: 98 Setting up I/O fencingAbout I/O
Page 100 and 101: 100 Setting up I/O fencingPreparing
Page 102 and 103: 102 Setting up I/O fencingPreparing
Page 104 and 105: 104 Setting up I/O fencingSetting u
Page 110 and 111: 110 Setting up I/O fencingAdditiona
Page 116 and 117:
116 Setting up I/O fencingHow I/O f
Page 118 and 119:
118 Setting up I/O fencingHow I/O f
Page 120 and 121:
120 Setting up I/O fencingAbout the
Page 122 and 123:
122 Setting up I/O fencingTroublesh
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
130 Verifying the VCS installationV
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
142 Verifying the VCS installationA
Page 144 and 145:
144 Upgrading to VCS 5.0Upgrading V
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
152 Upgrading to VCS 5.0Upgrading t
Page 154 and 155:
154 Upgrading to VCS 5.0
Page 156 and 157:
156 Adding and removing cluster nod
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
166 Installing VCS on a single node
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
178 Advanced topics related to inst
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
194 Configuring the Symantec Licens
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
200 IndexDdata disksfor I/O fencing
Page 202 and 203:
202 IndexrequirementsEthernet contr
Page 204:
204 Index
show all

Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...

Create successful ePaper yourself

Delete template?

Save as template?