Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...

More documents

Recommendations

Info

60 Installing and configuring VCSInstalling and configuring VCS 5.0Configuring global clustersYou can configure global clusters to link clusters at separate locations and enable wide-area failover and disaster recovery. Note that you must have entered a valid license key for VCS global clusters.To configure the global cluster option1 Review the required information to configure the global cluster option.2 Specify whether you want to configure the global cluster option. Do one ofthe following:■■To configure global cluster option, press Enter.Do you want to configure the Global Cluster Option? [y,n,q](y)To skip configuring global cluster option and advance to installing VCSpackages, enter n.See “Installing the VCS packages” on page 60.3 Provide information to configure the Global Cluster option.If you configured Cluster Management Console to manage this clusterlocally, the installer discovers and displays the virtual IP address andnetmask used by the Cluster Management Console. You can use the same virtual IP address and netmask.Do one of the following:■■If you want to use the default values, press Enter.If you do not want to use the default value, enter another IP address.The installer prompts you for a NIC and value for the netmask.Enter the Virtual IP address for Global Cluster Option:[b,?] (10.10.12.1)4 Verify and confirm the configuration of the global cluster.Global Cluster Option configuration verification:NIC: bge0IP: 10.10.12.1Netmask: 255.255.240.0Matching Cluster Management Console Virtual IP configurationIs this information correct? [y,n,q] (y)Installing the VCS packagesAfter the installer gathers all the configuration information, the installerinstalls the packages on the cluster systems. If you already installed the
Installing and configuring VCSInstalling and configuring VCS 5.061packages and chose to configure or reconfigure the cluster, the installerproceeds to create the configuration files.See “Creating VCS configuration files” on page 61.The utility checks for the required file system space and makes sure that anyprocesses that are running do not conflict with the installation. If requirementsfor installation are not met, the utility stops and indicates the actions requiredto proceed with the process. Review the output as the installer uninstalls anyprevious versions and installs the VCS 5.0 packages.Creating VCS configuration filesAfter installing the packages, the installer continues to create configurationfiles and copies them to each system:Creating Cluster Server configuration files ............ DoneCopying configuration files to north.................... DoneCopying configuration files to south.................... DoneCluster Server configured successfully.If you chose to configure the cluster in secure mode, the installer also configuresthe Symantec Product Authentication Service. Depending on the mode youchose to set up Authentication Service, the installer creates security principal orexecutes the encrypted file to create security principal on each node in thecluster. The installer creates the VxSS service group, creates AuthenticationServer credentials on each node in the cluster, and Web credentials for VCSusers, and sets up trust with the root broker. Then, the installer proceeds tostart VCS in secure mode.Starting VCSYou can now start VCS and its components on each system. If you chose toconfigure the cluster in secure mode, the installer also starts the AuthenticationService processes on each node in the cluster.To start VCS◆Confirm to start VCS and its components on each node.Do you want to start Veritas Cluster Server processes now? [y,n,q] (y) yCompleting the installationAfter VCS 5.0 installation completes successfully, the installer createssummary, log, and response files. The files provide useful information that canassist you with the installation and can also assist future installations. Table 3-5specifies the files created at the end of the installation.
Page 1 and 2:
Veritas Cluster ServerInstallation
Page 3:
Technical supportMake sure you have
Page 6 and 7:
6 ContentsSetting up shared storage
Page 8 and 9:
8 ContentsChapter 5Setting up I/O f
Page 10 and 11: 10 ContentsChapter 8Chapter 9Adding
Page 12 and 13: 12 Contents
Page 14 and 15: 14 Introducing VCSVCS basicsFigure
Page 16 and 17: 16 Introducing VCSVCS basicsNetwork
Page 18 and 19: 18 Introducing VCSVCS basics
Page 20 and 21: 20 Preparing to install and configu
Page 46 and 47: 46 Installing and configuring VCSAb
Page 48 and 49: 48 Installing and configuring VCSIn
Page 68 and 69: 68 Installing and configuring VCSPe
Page 76 and 77: 76 Installing and configuring VCSCh
Page 82 and 83: 82 Installing and configuring VCSUn
Page 84 and 85: 84 Manually installing and configur
Page 98 and 99: 98 Setting up I/O fencingAbout I/O
Page 100 and 101: 100 Setting up I/O fencingPreparing
Page 102 and 103: 102 Setting up I/O fencingPreparing
Page 104 and 105: 104 Setting up I/O fencingSetting u
Page 110 and 111:
110 Setting up I/O fencingAdditiona
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
116 Setting up I/O fencingHow I/O f
Page 118 and 119:
118 Setting up I/O fencingHow I/O f
Page 120 and 121:
120 Setting up I/O fencingAbout the
Page 122 and 123:
122 Setting up I/O fencingTroublesh
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
130 Verifying the VCS installationV
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
142 Verifying the VCS installationA
Page 144 and 145:
144 Upgrading to VCS 5.0Upgrading V
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
152 Upgrading to VCS 5.0Upgrading t
Page 154 and 155:
154 Upgrading to VCS 5.0
Page 156 and 157:
156 Adding and removing cluster nod
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
166 Installing VCS on a single node
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
178 Advanced topics related to inst
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
194 Configuring the Symantec Licens
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
200 IndexDdata disksfor I/O fencing
Page 202 and 203:
202 IndexrequirementsEthernet contr
Page 204:
204 Index
show all

Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...

Create successful ePaper yourself

Delete template?

Save as template?