Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...
Cluster Server Installation Guide for Solaris x64 5.0 - Storage ... Cluster Server Installation Guide for Solaris x64 5.0 - Storage ...
54 Installing and configuring VCSInstalling and configuring VCS 5.04 Review the NICs available on the first system as the installer discovers andreports them.5 Enter the details for the private heartbeat links.You must not enter the network interface card that is used for the publicnetwork (typically bge0.)Enter the NIC for the first private heartbeat NIC on north:[b,?] e1000g0Would you like to configure a second private heartbeat link?[y,n,q,b,?] (y)Enter the NIC for the second private heartbeat NIC on north:[b,?] e1000g1Would you like to configure a third private heartbeat link?[y,n,q,b,?](n) Do you want to configure an additional low priority heartbeat link? [y,n,q,b,?] (n)6 Choose whether to use the same NICs on all nodes.■■If you want to use the same NICs for private heartbeat links on allnodes, make sure the same NICs are available on each system and entery.Enter n to use NICs with different device names on some of the nodes.Are you using the same NICs for private heartbeat links on all systems? [y,n,q,b,?] (y)7 Verify and confirm the information that the installer summarizes.Configuring the cluster in secure modeBefore you configure a cluster in a secure mode, make sure to meet therequirements for automatic or semiautomatic mode of configuration. You canalso enable Symantec Product Authentication Service later.See “Symantec Product Authentication Service” on page 20.To configure the cluster in secure mode1 Choose whether to configure VCS to use Symantec Product AuthenticationService.Would you like to configure VCS to use Symantec Security Services? [y,n,q] (n) y■■If you want to configure the cluster in secure mode, make sure you haveinstalled the root broker and enter y.If you do not want to configure the cluster in secure mode and want toproceed to adding VCS users, enter n.See “Adding VCS users” on page 56.2 Select one of the options to enable security.
Installing and configuring VCSInstalling and configuring VCS 5.055Select the Security option you would like to perform [1-3,q,?]Based on the mode of configuration you want to use, enter one of thefollowing:OptionTasks1. Automatic Enter the name of the Root Broker system when prompted.configurationRequires remote access to the Root Broker.Review the output as the installer verifies communication withthe Root Broker system, checks vxatd process and version, andchecks security domain.2 . Semi-automatic Enter the path of the file for each node when prompted.using encryptedfiles3. Semi-automatic Enter the following Root Broker information as the installerenteringprompts you:authentication Enter root Broker name: information at east.symantecexample.cominstaller prompts Enter root broker FQDN: [b] (symantecexample.com) symantecexample.comEnter root broker domain: [b] (root@east.symantecexample.com) root@east.symantecexample.comEnter root broker port: [b] (2821) 2821Enter path to the locally accessible root hash [b] (/var/tmp/installvcs-1Lcljr/root_hash) /root/root_hashEnter the following Authentication Broker information as theinstaller prompts you for each node:Enter authentication broker principal name on north [b](north.symantecexample.com) north.symantecexample.comEnter authentication broker password on north: Enter authentication broker principal name on south [b](south.symantecexample.com) south.symantecexample.comEnter authentication broker password on south: 3After configuring the cluster in secure mode, proceed to configure the Cluster Management Console cluster connector.See “Configuring cluster connector” on page 56.
- Page 3: Technical supportMake sure you have
- Page 6 and 7: 6 ContentsSetting up shared storage
- Page 8 and 9: 8 ContentsChapter 5Setting up I/O f
- Page 10 and 11: 10 ContentsChapter 8Chapter 9Adding
- Page 12 and 13: 12 Contents
- Page 14 and 15: 14 Introducing VCSVCS basicsFigure
- Page 16 and 17: 16 Introducing VCSVCS basicsNetwork
- Page 18 and 19: 18 Introducing VCSVCS basics
- Page 20 and 21: 20 Preparing to install and configu
- Page 22 and 23: 22 Preparing to install and configu
- Page 24 and 25: 24 Preparing to install and configu
- Page 26 and 27: 26 Preparing to install and configu
- Page 28 and 29: 28 Preparing to install and configu
- Page 30 and 31: 30 Preparing to install and configu
- Page 32 and 33: 32 Preparing to install and configu
- Page 34 and 35: 34 Preparing to install and configu
- Page 36 and 37: 36 Preparing to install and configu
- Page 38 and 39: 38 Preparing to install and configu
- Page 40 and 41: 40 Preparing to install and configu
- Page 42 and 43: 42 Preparing to install and configu
- Page 44 and 45: 44 Preparing to install and configu
- Page 46 and 47: 46 Installing and configuring VCSAb
- Page 48 and 49: 48 Installing and configuring VCSIn
- Page 50 and 51: 50 Installing and configuring VCSIn
- Page 52 and 53: 52 Installing and configuring VCSIn
- Page 56 and 57: 56 Installing and configuring VCSIn
- Page 58 and 59: 58 Installing and configuring VCSIn
- Page 60 and 61: 60 Installing and configuring VCSIn
- Page 62 and 63: 62 Installing and configuring VCSIn
- Page 64 and 65: 64 Installing and configuring VCSIn
- Page 66 and 67: 66 Installing and configuring VCSIn
- Page 68 and 69: 68 Installing and configuring VCSPe
- Page 70 and 71: 70 Installing and configuring VCSPe
- Page 72 and 73: 72 Installing and configuring VCSPe
- Page 74 and 75: 74 Installing and configuring VCSPe
- Page 76 and 77: 76 Installing and configuring VCSCh
- Page 78 and 79: 78 Installing and configuring VCSAb
- Page 80 and 81: 80 Installing and configuring VCSAb
- Page 82 and 83: 82 Installing and configuring VCSUn
- Page 84 and 85: 84 Manually installing and configur
- Page 86 and 87: 86 Manually installing and configur
- Page 88 and 89: 88 Manually installing and configur
- Page 90 and 91: 90 Manually installing and configur
- Page 92 and 93: 92 Manually installing and configur
- Page 94 and 95: 94 Manually installing and configur
- Page 96 and 97: 96 Manually installing and configur
- Page 98 and 99: 98 Setting up I/O fencingAbout I/O
- Page 100 and 101: 100 Setting up I/O fencingPreparing
- Page 102 and 103: 102 Setting up I/O fencingPreparing
54 Installing and configuring VCSInstalling and configuring VCS <strong>5.0</strong>4 Review the NICs available on the first system as the installer discovers andreports them.5 Enter the details <strong>for</strong> the private heartbeat links.You must not enter the network interface card that is used <strong>for</strong> the publicnetwork (typically bge0.)Enter the NIC <strong>for</strong> the first private heartbeat NIC on north:[b,?] e1000g0Would you like to configure a second private heartbeat link?[y,n,q,b,?] (y)Enter the NIC <strong>for</strong> the second private heartbeat NIC on north:[b,?] e1000g1Would you like to configure a third private heartbeat link?[y,n,q,b,?](n) Do you want to configure an additional low priority heartbeat link? [y,n,q,b,?] (n)6 Choose whether to use the same NICs on all nodes.■■If you want to use the same NICs <strong>for</strong> private heartbeat links on allnodes, make sure the same NICs are available on each system and entery.Enter n to use NICs with different device names on some of the nodes.Are you using the same NICs <strong>for</strong> private heartbeat links on all systems? [y,n,q,b,?] (y)7 Verify and confirm the in<strong>for</strong>mation that the installer summarizes.Configuring the cluster in secure modeBe<strong>for</strong>e you configure a cluster in a secure mode, make sure to meet therequirements <strong>for</strong> automatic or semiautomatic mode of configuration. You canalso enable Symantec Product Authentication Service later.See “Symantec Product Authentication Service” on page 20.To configure the cluster in secure mode1 Choose whether to configure VCS to use Symantec Product AuthenticationService.Would you like to configure VCS to use Symantec Security Services? [y,n,q] (n) y■■If you want to configure the cluster in secure mode, make sure you haveinstalled the root broker and enter y.If you do not want to configure the cluster in secure mode and want toproceed to adding VCS users, enter n.See “Adding VCS users” on page 56.2 Select one of the options to enable security.