Dinion IP - NWC-0495 - Bosch
Dinion IP - NWC-0495 - Bosch Dinion IP - NWC-0495 - Bosch
Dinion IP | Installation ManualEN | 89Troubleshooting 10If you cannot resolve a fault, please contact your supplier or system integrator orgo direct to Bosch Security Systems Customer Service.The version numbers of the internal processors can be viewed on a special page.Please note this information before contacting Customer Service.– In the address bar of your browser, after the unit IP address enter/version.htm (for example 192.168.0.80/version.htm).– Write down the information or print out the page.The following table is intended to help you identify the causes of malfunctionsand correct them where possible.Malfunction Possible causes SolutionNo imagetransmission toremote location.No connectionestablished, no imagetransmission.The unit does notreport an alarm.Defective camera.Faulty cable connections.The unit's configuration.Faulty installation.Wrong IP address.Faulty data transmissionwithin the LAN.The maximum number ofconnections has beenreached.Alarm source is not selected.No alarm response specified.Connect a local monitor to thecamera and check the camerafunction.Check all cables, plugs, contactsand connections.Check all configuration parameters.Check all cables, plugs, contactsand connections.Check the IP addresses (terminalprogram).Check the data transmission withping.Wait until there is a free connectionand call the transmitter again.Select possible alarm sources onthe Alarm sources configurationpage.Specify the desired alarm responseon the Alarm connectionsconfiguration page, if necessarychange the IP address.Bosch Security Systems | 2006-05 | V2.0
EN | 90Dinion IP | Installation ManualMalfunction Possible causes SolutionThe unit is notoperational afterfirmware upload.Power failure duringprogramming by the updatefile.Have the unit checked by CustomerService and replace if necessary.Incorrect update file. Enter the IP address followed by /main.htm in your web browserand repeat the upload.Bosch Security Systems | 2006-05 | V2.0
- Page 39 and 40: EN | 38Dinion IP | Installation Man
- Page 41: EN | 40Dinion IP | Installation Man
- Page 45 and 46: EN | 44Dinion IP | Installation Man
- Page 47 and 48: EN | 46Dinion IP | Installation Man
- Page 49 and 50: EN | 48Dinion IP | Installation Man
- Page 51 and 52: EN | 50Dinion IP | Installation Man
- Page 53 and 54: EN | 52Dinion IP | Installation Man
- Page 55 and 56: EN | 54Dinion IP | Installation Man
- Page 57 and 58: EN | 56Dinion IP | Installation Man
- Page 59 and 60: EN | 58Dinion IP | Installation Man
- Page 61 and 62: EN | 60Dinion IP | Installation Man
- Page 63 and 64: EN | 62Dinion IP | Installation Man
- Page 65 and 66: EN | 64Dinion IP | Installation Man
- Page 67 and 68: EN | 66Dinion IP | Installation Man
- Page 69 and 70: EN | 68Dinion IP | Installation Man
- Page 71 and 72: EN | 70Dinion IP | Installation Man
- Page 73 and 74: EN | 72Dinion IP | Installation Man
- Page 75 and 76: EN | 74Dinion IP | Installation Man
- Page 77 and 78: EN | 76Dinion IP | Installation Man
- Page 79 and 80: EN | 78Dinion IP | Installation Man
- Page 81 and 82: EN | 80Dinion IP | Installation Man
- Page 83 and 84: EN | 82Dinion IP | Installation Man
- Page 85 and 86: EN | 84Dinion IP | Installation Man
- Page 87 and 88: EN | 86Dinion IP | Installation Man
- Page 89: EN | 88Dinion IP | Installation Man
- Page 93 and 94: EN | 92Dinion IP | Installation Man
- Page 95 and 96: EN | 94Dinion IP | Installation Man
- Page 97 and 98: EN | 96Dinion IP | Installation Man
- Page 99: Bosch Sicherheitssysteme GmbHLudwig
<strong>Dinion</strong> <strong>IP</strong> | Installation ManualEN | 89Troubleshooting 10If you cannot resolve a fault, please contact your supplier or system integrator orgo direct to <strong>Bosch</strong> Security Systems Customer Service.The version numbers of the internal processors can be viewed on a special page.Please note this information before contacting Customer Service.– In the address bar of your browser, after the unit <strong>IP</strong> address enter/version.htm (for example 192.168.0.80/version.htm).– Write down the information or print out the page.The following table is intended to help you identify the causes of malfunctionsand correct them where possible.Malfunction Possible causes SolutionNo imagetransmission toremote location.No connectionestablished, no imagetransmission.The unit does notreport an alarm.Defective camera.Faulty cable connections.The unit's configuration.Faulty installation.Wrong <strong>IP</strong> address.Faulty data transmissionwithin the LAN.The maximum number ofconnections has beenreached.Alarm source is not selected.No alarm response specified.Connect a local monitor to thecamera and check the camerafunction.Check all cables, plugs, contactsand connections.Check all configuration parameters.Check all cables, plugs, contactsand connections.Check the <strong>IP</strong> addresses (terminalprogram).Check the data transmission withping.Wait until there is a free connectionand call the transmitter again.Select possible alarm sources onthe Alarm sources configurationpage.Specify the desired alarm responseon the Alarm connectionsconfiguration page, if necessarychange the <strong>IP</strong> address.<strong>Bosch</strong> Security Systems | 2006-05 | V2.0