Dinion IP - NWC-0495 - Bosch
Dinion IP - NWC-0495 - Bosch Dinion IP - NWC-0495 - Bosch
Dinion IP | Installation ManualEN | 67Alarm SettingsHere, you can make the settings for the alarm sources and alarm connections.Alarm inYou can configure the possible alarm triggers for the camera.Alarm input 1Select the option On in order to activate the alarm via the correspondingexternal alarm sensor. Otherwise, select Off.Select Active Low if the alarm is to be triggered by closing the contact. SelectActive High if the alarm is to be triggered by opening the contact.NameYou can enter a name for each alarm input, which is then displayed below theicon for the alarm input on the Livepage during configuration.Alarm connectionsYou can select the response of the camera in case of an alarm. In case of an alarm,the camera can automatically establish a connection to a predefined IP address(compatible MPEG-4 compatible hardware receiver or computer with receptionsoftware). You can enter up to ten IP addresses which will be selected in order bythe unit in case of an alarm until a connection is established.Bosch Security Systems | 2006-05 | V2.0
EN | 68Dinion IP | Installation ManualConnect on alarmSelect On so that the camera automatically establishes a connection to a predefinedIP address in the event of an alarm.NoteStream 2 is always transmitted for alarm connections. This should be takeninto account when assigning the profile.Number of destination IP addressHere you assign the numbering for the IP addresses to be contacted in the eventof an alarm. The unit contacts the remote locations one after the other in thenumbered sequence until a connection has been established.Destination IP addressFor each number, enter the corresponding IP address for the desired remotelocation.Destination passwordIf the remote location is password protected, enter the password here.Auto-connectSelect On if an active connection should be re-established automatically to one ofthe previously specified IP addresses after each restart, connection breakdown ornetwork failure.NoteStream 2 is always transmitted for automatic connections. This should betaken into account when assigning the profile.Bosch Security Systems | 2006-05 | V2.0
- Page 17 and 18: EN | 16Dinion IP | Installation Man
- Page 19 and 20: EN | 18Dinion IP | Installation Man
- Page 21 and 22: EN | 20Dinion IP | Installation Man
- Page 23 and 24: EN | 22Dinion IP | Installation Man
- Page 25 and 26: EN | 24Dinion IP | Installation Man
- Page 27 and 28: EN | 26Dinion IP | Installation Man
- Page 29 and 30: EN | 28Dinion IP | Installation Man
- Page 31 and 32: EN | 30Dinion IP | Installation Man
- Page 33 and 34: EN | 32Dinion IP | Installation Man
- Page 35 and 36: EN | 34Dinion IP | Installation Man
- Page 37 and 38: EN | 36Dinion IP | Installation Man
- Page 39 and 40: EN | 38Dinion IP | Installation Man
- Page 41: EN | 40Dinion IP | Installation Man
- Page 45 and 46: EN | 44Dinion IP | Installation Man
- Page 47 and 48: EN | 46Dinion IP | Installation Man
- Page 49 and 50: EN | 48Dinion IP | Installation Man
- Page 51 and 52: EN | 50Dinion IP | Installation Man
- Page 53 and 54: EN | 52Dinion IP | Installation Man
- Page 55 and 56: EN | 54Dinion IP | Installation Man
- Page 57 and 58: EN | 56Dinion IP | Installation Man
- Page 59 and 60: EN | 58Dinion IP | Installation Man
- Page 61 and 62: EN | 60Dinion IP | Installation Man
- Page 63 and 64: EN | 62Dinion IP | Installation Man
- Page 65 and 66: EN | 64Dinion IP | Installation Man
- Page 67: EN | 66Dinion IP | Installation Man
- Page 71 and 72: EN | 70Dinion IP | Installation Man
- Page 73 and 74: EN | 72Dinion IP | Installation Man
- Page 75 and 76: EN | 74Dinion IP | Installation Man
- Page 77 and 78: EN | 76Dinion IP | Installation Man
- Page 79 and 80: EN | 78Dinion IP | Installation Man
- Page 81 and 82: EN | 80Dinion IP | Installation Man
- Page 83 and 84: EN | 82Dinion IP | Installation Man
- Page 85 and 86: EN | 84Dinion IP | Installation Man
- Page 87 and 88: EN | 86Dinion IP | Installation Man
- Page 89 and 90: EN | 88Dinion IP | Installation Man
- Page 91 and 92: EN | 90Dinion IP | Installation Man
- Page 93 and 94: EN | 92Dinion IP | Installation Man
- Page 95 and 96: EN | 94Dinion IP | Installation Man
- Page 97 and 98: EN | 96Dinion IP | Installation Man
- Page 99: Bosch Sicherheitssysteme GmbHLudwig
EN | 68<strong>Dinion</strong> <strong>IP</strong> | Installation ManualConnect on alarmSelect On so that the camera automatically establishes a connection to a predefined<strong>IP</strong> address in the event of an alarm.NoteStream 2 is always transmitted for alarm connections. This should be takeninto account when assigning the profile.Number of destination <strong>IP</strong> addressHere you assign the numbering for the <strong>IP</strong> addresses to be contacted in the eventof an alarm. The unit contacts the remote locations one after the other in thenumbered sequence until a connection has been established.Destination <strong>IP</strong> addressFor each number, enter the corresponding <strong>IP</strong> address for the desired remotelocation.Destination passwordIf the remote location is password protected, enter the password here.Auto-connectSelect On if an active connection should be re-established automatically to one ofthe previously specified <strong>IP</strong> addresses after each restart, connection breakdown ornetwork failure.NoteStream 2 is always transmitted for automatic connections. This should betaken into account when assigning the profile.<strong>Bosch</strong> Security Systems | 2006-05 | V2.0