DALI manual - Tridonic

More documents

Recommendations

Info

.cDALI sequencer module: DALI SQMSet number of scenes in the sequencePress UP button to increase number of scenes in the sequence by onePress DOWN button to decrease number of scenen in the sequence by oneHold DOWN button down to save number of scenesI NOTICEBy default 8 scenes are preset. A maximum of 16 scenes can be set.Switch off lightHold DOWN button down to switch off the connected luminairesThe DALI SQM is activated via a floating contact. When the contact is closed the module is active and continuallysends DALI scene calls. The delay time between the scene calls (step time) can be set on a rotary switch on themodule (shortest time 1 second, longest time 30 minutes). A switch on the module allows you to select the scene afterwhich the sequence starts from the beginning again. The brightness values for the different scenes are set with theDALI GC and SC or via the masterCONFIGURATOR.Cross-fade the DALI SQMCross-fading from scene to scene is determined by the fade time of the DALI ballasts. The range is from 0.7 secondsto 90.5 seconds and is set via the masterCONFIGURATOR software. For more information on setting the fade timeplease refer to the operating instructions for the masterCONFIGURATOR (see Reference list).Figure: DALI SQM cross-fadeI NOTICE...If the step time is less than the fade time the next scene will be selected even if the scene has not been completed.DALI Manual | 08-2013 | en52 / 93
.cDALI MSensor 02DALI MSensor 02DescriptionThe DALI MSensor 02 is a digital controller in the comfortDIM product range that can be used to control the controlgear of a DALI group collectively. The sensor combines three functions in one control device:Constant light controlPresence-based controlRemote controlThe DALI MSensor 02 is is available in four different housing designs:Fitted in luminaire Recessed into ceiling Surface-mounted Box-mountedThe DALI MSensor 02 is designed for the following principal applications:Individual officesOpen-plan officesTraining/presentation roomsCorridors, passageways and garagesThe DALI MSensor 02 either controls all the units on the DALI circuit or a DALI group. The DALI MSensor 02 isMulti-master compatible, i.e. it can be used in conjunction with other DALI controllers in the comfortDIM product range.This allows the DALI MSensor 02 to be addressed and grouped in the same way as DALI control gear and makes iteasy to configure the system.The DALI MSensors 02 is configured in the masterCONFIGURATOR software (V2.02. or later) (see Reference list).ConnectionThe DALI MSensor 02 is connected directly to the DALI circuit and does not need a separate power supply. It ispowered via the DALI circuit (current draw = 6 mA). It can be connected to the DALI circuit with either polarity.FunctionsThe DALI MSensor 02 has the following functions and user interfaces:Constant light control by means of ambient light sensorDALI Manual | 08-2013 | en53 / 93
Page 1: luxCONTROLDALI manual
Page 7 and 8: .cIntroduction: DALI standardPositi
Page 9 and 10: .cDALI controllers of comfortDIM pr
Page 15 and 16: .cDALI devicesDALI devicesElectroni
Page 17 and 18: .cDALI devicesElectronic HID contro
Page 20 and 21: .cMiscellaneousMiscellaneousDALI Re
Page 22 and 23: .cDALI power supplyFigure: Delay an
Page 24 and 25: .cDALI group controllers: DALI GC &
Page 32 and 33: .cDALI scene controllers: DALI-SC &
Page 34 and 35: .cDALI scene controllers: DALI-SC &
Page 36 and 37: .cDALI multi controller: DALI MCFun
Page 38 and 39: .cDALI multi controller: DALI MC10)
Page 40 and 41: .cDALI multi controller: DALI MCExa
Page 42 and 43: .cDALI TOUCHPANEL 02DALI TOUCHPANEL
Page 44 and 45: .cDALI TOUCHPANEL 02Table: Paramete
Page 46 and 47: .cDALI x/e-touchPANEL 02DALI x/e-to
Page 48 and 49: .cDALI x/e-touchPANEL 02Colour oper
Page 50 and 51: .cDALI x/e-touchPANEL 02Wiring diag
Page 54 and 55: .cDALI MSensor 02Constant light con
Page 56 and 57: .cDALI MSensor 02Figure: Overview o
Page 58 and 59: .cDesigning a DALI applicationDesig
Page 60 and 61: .cDesigning a DALI applicationCalcu
Page 62 and 63: .cDesigning a DALI applicationFigur
Page 64 and 65: .cDesigning a DALI applicationFigur
Page 66 and 67: .cDesigning a DALI applicationTable
Page 68 and 69: .cDesigning a DALI applicationTable
Page 70 and 71: .cStart-upStart-upThere are various
Page 72 and 73: .cStart-upTable: Parts listPos. Qty
Page 74 and 75: .cStart-upFigure: Up and down switc
Page 76 and 77: .cStart-upSetting up without softwa
Page 78 and 79: .cStart-upSelect “Start Test”
Page 80 and 81: .cStart-up( 1 ) ( 2 ) ( 3 ) ( 4 ) (
Page 82 and 83: .cMaintenance and troubleshootingMa
Page 84 and 85: .cMaintenance and troubleshootingEx
Page 86 and 87: .cAnnexAnnexTechnical features of a
Page 88 and 89: .cAnnexTable: Important DALI comman
Page 90 and 91: .cAnnexTable: Overview DALI power s
Page 92 and 93: .cAnnexGO TO SCENE XCan be set usin

DALI manual - Tridonic

Create successful ePaper yourself

Delete template?

Save as template?