DALI manual - Tridonic

More documents

Recommendations

Info

.cDALI multi controller: DALI MCFunctionThe behaviour of each of the four inputs can be defined with the aid of the masterCONFIGURATOR software. Possiblesettings are:The input functions asa push to make switcha standard switcha changeover switcha stairwell switcha push to make switch that calls up a predefined sequence of DALI commands (macro)In addition to defining the function you can set further parameters to select the destination address for which thefunction is intended (broadcast, group or individual address) and the type of DALI command to be performed.Example: On/off switchDestination address Group 1FunctionDALI commandSwitch“Recall max. Level” when switched on and “OFF” when switched offConfiguration by masterCONFIGURATORThe masterCONFIGURATOR has its own separate documentation (see Reference list).DALI Manual | 08-2013 | en36 / 93
.cDALI multi controller: DALI MCTable: Explanation of parameters for functionsFunction1) Push-button:short or long = 1 * command X2) Push-button:short = 1 * command X,long = 1 * command X then 1 *command Y3) Push-button:short = 1 * command X,long = 1 * command X thenrepeatedly command YDescriptionBriefly pressing or holding down the push-button will send command X onetime.» Briefly pressing the push-button will send command X one time.» Holding down the push-button will send command X once, and thencommand Y once.» Briefly pressing the push-button will send command X one time.» Holding down the push-button will send command X once, and thencommand Y repeatedly.4) Push-button:short = 1* command X,long = repeatedly command Y»»Briefly pressing the push-button will send command X one time.Holding down the push-button will repeatedly send command Y.5) Push-button (toggle):short or long = toggle betweencommand X and Y6) Push-button (toggle):short or long = toggle betweencommand X and Y,lighting-based7) Push-button (dimming key):short = toggle between commandX and Y,long = dimming, lighting-basedBriefly pressing or holding down the push-button will alternate between sendingcommands X and Y.Briefly pressing or holding down the push-button will alternate between sendingcommands X and Y. The command sent in each case depends on the status ofthe lighting:» If the lighting was previously switched off, command X is sent.» If the lighting was previously switched on, command Y is sent.SwitchDIM mode» Briefly pressing on the dimming key will alternate between sendingcommands X and Y. The command sent in each case depends on thestatus of the lighting.» If the lighting was previously switched off, command X is sent.» If the lighting was previously switched on, command Y is sent. Holdingdown the dimmer switch dims or brightens the lighting.8) Switch:close = command X,open = command Y»»When the switch is closed, command X is sent.When the switch is opened, command Y is sent.9) Changeover switch:close = command X,open = command Y,lighting-basedEach time the switch is pressed, the commands X and Y are sent in alternatingorder. The command sent in each case depends on the status of the lighting:» If the lighting was previously switched off, command X is sent.» If the lighting was previously switched on, command Y is sent.DALI Manual | 08-2013 | en37 / 93
Page 1: luxCONTROLDALI manual
Page 7 and 8: .cIntroduction: DALI standardPositi
Page 9 and 10: .cDALI controllers of comfortDIM pr
Page 15 and 16: .cDALI devicesDALI devicesElectroni
Page 17 and 18: .cDALI devicesElectronic HID contro
Page 20 and 21: .cMiscellaneousMiscellaneousDALI Re
Page 22 and 23: .cDALI power supplyFigure: Delay an
Page 24 and 25: .cDALI group controllers: DALI GC &
Page 32 and 33: .cDALI scene controllers: DALI-SC &
Page 34 and 35: .cDALI scene controllers: DALI-SC &
Page 38 and 39: .cDALI multi controller: DALI MC10)
Page 40 and 41: .cDALI multi controller: DALI MCExa
Page 42 and 43: .cDALI TOUCHPANEL 02DALI TOUCHPANEL
Page 44 and 45: .cDALI TOUCHPANEL 02Table: Paramete
Page 46 and 47: .cDALI x/e-touchPANEL 02DALI x/e-to
Page 48 and 49: .cDALI x/e-touchPANEL 02Colour oper
Page 50 and 51: .cDALI x/e-touchPANEL 02Wiring diag
Page 52 and 53: .cDALI sequencer module: DALI SQMSe
Page 54 and 55: .cDALI MSensor 02Constant light con
Page 56 and 57: .cDALI MSensor 02Figure: Overview o
Page 58 and 59: .cDesigning a DALI applicationDesig
Page 60 and 61: .cDesigning a DALI applicationCalcu
Page 62 and 63: .cDesigning a DALI applicationFigur
Page 64 and 65: .cDesigning a DALI applicationFigur
Page 66 and 67: .cDesigning a DALI applicationTable
Page 68 and 69: .cDesigning a DALI applicationTable
Page 70 and 71: .cStart-upStart-upThere are various
Page 72 and 73: .cStart-upTable: Parts listPos. Qty
Page 74 and 75: .cStart-upFigure: Up and down switc
Page 76 and 77: .cStart-upSetting up without softwa
Page 78 and 79: .cStart-upSelect “Start Test”
Page 80 and 81: .cStart-up( 1 ) ( 2 ) ( 3 ) ( 4 ) (
Page 82 and 83: .cMaintenance and troubleshootingMa
Page 84 and 85: .cMaintenance and troubleshootingEx
Page 86 and 87:
.cAnnexAnnexTechnical features of a
Page 88 and 89:
.cAnnexTable: Important DALI comman
Page 90 and 91:
.cAnnexTable: Overview DALI power s
Page 92 and 93:
.cAnnexGO TO SCENE XCan be set usin
show all

DALI manual - Tridonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?