DALI manual - Tridonic

More documents

Recommendations

Info

.cDALI group controllers: DALI GC & GC-AStart programming mode without deletion of addresses (expansion of the system)Connect standard momentary switch to DALI GCChoose a button and hold down (>10 s)→ A beep will soundRelease button briefly (1s)→ A beep will sound againHold button down (1s)→ Two beeps will soundRelease button→ Device switches to programming mode→ Current settings (group assignment) won't be deletedFigure: Programming mode without deleting the addressesStart programming mode with deletion of addresses (new installation)Connect standard momentary switch to DALI GCChoose a button and hold down (>10 s)→ A beep will soundRelease button briefly (1s)→ A beep will sound againHold button down (>3s)→ Two beeps will sound (after 1s)→ Three more beeps will sound (after 3s)Release button→ Device switches to programming mode→ Current settings (group assignment) will be deletedDALI Manual | 08-2013 | en26 / 93
.cDALI group controllers: DALI GC & GC-AFigure: Programming mode with deletion of addressesI NOTICEIn programming mode the system first searches for available DALI devices in the DALI circuit. The devices areaddressed as follows:In programming mode with deletion all devices will be automatically addressedIn programming mode without deletion only newly detected devices are addressedDuring the search operation all the detected luminaires are faded to maximum. When the search has beencompleted one luminaire (the one selected) will remain at maximum and all the others will be faded to the lowestvalue.Selecting luminairesTo attach a luminaire to a group, the luminaire must be selected first.Choose a button of the momentary switchPress button briefly to select a luminaire→ Selected luminaire is faded to maximum→ All other luminaires are dimmed to minimumPress button again to select another luminaireI NOTICEA single luminaire can contain more than one device. If this is the case all devices in the luminaire must be selectedseparately.The luminaires are selected in the sequence in which they are found. When you come to the last luminaire in thesequence, the next one selected will be the first luminaire in the sequence again. A selected luminaire can now beassigned to a group.Assigning a selected luminaire to a groupIf a luminaire is assigned to a certain group it reacts to fade commands that come from momentary switches of thesame group. The group assigned can be stored in the selected DALI device.Make sure that the right luminaire is selectedChoose a button that is assigned to the right groupDALI Manual | 08-2013 | en27 / 93
Page 1: luxCONTROLDALI manual
Page 7 and 8: .cIntroduction: DALI standardPositi
Page 9 and 10: .cDALI controllers of comfortDIM pr
Page 15 and 16: .cDALI devicesDALI devicesElectroni
Page 17 and 18: .cDALI devicesElectronic HID contro
Page 20 and 21: .cMiscellaneousMiscellaneousDALI Re
Page 22 and 23: .cDALI power supplyFigure: Delay an
Page 24 and 25: .cDALI group controllers: DALI GC &
Page 32 and 33: .cDALI scene controllers: DALI-SC &
Page 34 and 35: .cDALI scene controllers: DALI-SC &
Page 36 and 37: .cDALI multi controller: DALI MCFun
Page 38 and 39: .cDALI multi controller: DALI MC10)
Page 40 and 41: .cDALI multi controller: DALI MCExa
Page 42 and 43: .cDALI TOUCHPANEL 02DALI TOUCHPANEL
Page 44 and 45: .cDALI TOUCHPANEL 02Table: Paramete
Page 46 and 47: .cDALI x/e-touchPANEL 02DALI x/e-to
Page 48 and 49: .cDALI x/e-touchPANEL 02Colour oper
Page 50 and 51: .cDALI x/e-touchPANEL 02Wiring diag
Page 52 and 53: .cDALI sequencer module: DALI SQMSe
Page 54 and 55: .cDALI MSensor 02Constant light con
Page 56 and 57: .cDALI MSensor 02Figure: Overview o
Page 58 and 59: .cDesigning a DALI applicationDesig
Page 60 and 61: .cDesigning a DALI applicationCalcu
Page 62 and 63: .cDesigning a DALI applicationFigur
Page 64 and 65: .cDesigning a DALI applicationFigur
Page 66 and 67: .cDesigning a DALI applicationTable
Page 68 and 69: .cDesigning a DALI applicationTable
Page 70 and 71: .cStart-upStart-upThere are various
Page 72 and 73: .cStart-upTable: Parts listPos. Qty
Page 74 and 75: .cStart-upFigure: Up and down switc
Page 76 and 77:
.cStart-upSetting up without softwa
Page 78 and 79:
.cStart-upSelect “Start Test”
Page 80 and 81:
.cStart-up( 1 ) ( 2 ) ( 3 ) ( 4 ) (
Page 82 and 83:
.cMaintenance and troubleshootingMa
Page 84 and 85:
.cMaintenance and troubleshootingEx
Page 86 and 87:
.cAnnexAnnexTechnical features of a
Page 88 and 89:
.cAnnexTable: Important DALI comman
Page 90 and 91:
.cAnnexTable: Overview DALI power s
Page 92 and 93:
.cAnnexGO TO SCENE XCan be set usin
show all

DALI manual - Tridonic

Create successful ePaper yourself

Delete template?

Save as template?