User Manual M3000® Automation System / MSC II (Moog Servo ...

More documents

Recommendations

Info

10 MSC II (Moog Servo Controller) View of the Module and Terminal Assignment Connector No. Assignment Circuit X14 RT-ETH1 X15 RT-ETH2 10.4.2 LEDs 1 Tx+ Transmit data+ 2 Tx- Transmit data- 3 4 5 Rx+ Receive data+ 6 7 8 Rx- Receive data- 1 Tx+ Transmit data+ 2 Tx- Transmit data- 3 4 5 Rx+ Receive data+ 6 7 8 Rx- Receive data- Table 16: Terminal Assignment of MSC II's Connectors (Section 4 of 4) Area LED Display Explanation Status L1+ L1+/M1 and internal +5 V ok Illuminates when the power supply for the MSC II's internal electronics is OK and the internal power pack is supplying +5 V. �-"6.2-Power Supply" on page 39 TRM Termination resistor on LocalCAN Illuminates when the termination resistor of the LocalCAN interface is switched on. �-"10.15.1-CAN Bus Termination Resistor" on page 110 I/O1 Internal status of the digital I/O-1 �-"10.10.1-Display of the Operational State" on page 93 I/O2 Internal status of the digital I/O-2 I/O3 Internal status of the digital I/O-3 I/O4 Internal status of the digital I/O-4 WCAN WideCAN transmission activity Flashes in synchronization with the data that the MSC II is sending over the WideCAN interface. �-"10.15-CAN Bus Interfaces" on page 109 LCAN LocalCAN transmission activity Flashes in synchronization with the data that the MSC II is sending over the LocalCAN interface. �-"10.15-CAN Bus Interfaces" on page 109 EBus E-bus transmission activity Illuminates when the MSC II is sending data over the E-bus. �-"7.6.3-MSC II as E-Bus Master" on page 61 Rx SIO receiver activity Illuminates when the MSC II is receiving data over the SIO interface Tx SIO transmission activity Illuminates when the MSC II is sending data over the SIO interfaces. �-Table-18 on page 83 User Aux1 Activated by application program Illuminates when the application program activates the LED. Aux2 Activated by application program Aux3 Activated by application program Aux4 Activated by application program Table 17: LEDs of the MSC II (Section 1 of 2) © Moog GmbH User Manual M3000 ® and MSC II (CA65865-001; Version 1.1, 08/08) 81 Ethernet (RT-ETH1) Ethernet (RT-ETH2)
10 MSC II (Moog Servo Controller) View of the Module and Terminal Assignment Area LED Display Explanation OutEN Outputs enabled Illuminates when all outputs and the E-bus communication are under the control of the application program. �-"10.17.2-'Outputs Enabled' Output (LED «OutEN»)" on page 111 Error A1 Wire fault in the digital sensor input-A1 Illuminates when no receiver is attached to the corresponding digital B1 Z1 Wire fault in the digital sensor input-B1 Wire fault in the digital sensor input-Z1 sensor interface or when there is a wire fault. �-"10.13.2.1-Wire Fault Display LEDs" on page 102 A2 Wire fault in the digital sensor input-A2 B2 Wire fault in the digital sensor input-B2 Z2 Wire fault in the digital sensor input-Z2 A3 Wire fault in the digital sensor input-A3 B3 Wire fault in the digital sensor input-B3 Z3 Wire fault in the digital sensor input-Z3 A4 Wire fault in the digital sensor input-A4 B4 Wire fault in the digital sensor input-B4 Z4 Wire fault in the digital sensor input-Z4 User LED1 Activated by application program or error display LED2 Activated by application program or error display LED3 Activated by application program or error display As long as LED «Error» does not illuminate, the application program can activate these LEDs (provided that the MSC II has successfully started and that the application program has started). The states that these LEDs will indicate while the application program is running are set in the application program. If «Error» illuminates or flashes in addition to these LEDs, this indicates MSC II's elementary operational states or errors. �-Table-18 on page 83 Error Error display Illuminates when there is an error. The type of error is specified in «LED1», «LED2», and «LED3». �-Table-18 on page 83 Ethernet Link Ethernet link/activity Illuminates when the Ethernet link pulse is available and blinks at activity Speed On = 100 Mbit/s Ethernet connection speed Table 17: LEDs of the MSC II (Section 2 of 2) © Moog GmbH User Manual M3000 ® and MSC II (CA65865-001; Version 1.1, 08/08) 82
Page 1 and 2:
User Manual M3000 ® Automation Sys
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 7.6 E-Bus .......
Page 7 and 8:
Table of Contents 13 Index.........
Page 9 and 10:
List of Tables Table 36: Product Ra
Page 11 and 12:
List of Figures Figure 38: 100BaseT
Page 13 and 14:
1 General Information Selection and
Page 15 and 16:
1 General Information Environmental
Page 17 and 18:
2 Safety Instructions Typographical
Page 19 and 20:
2 Safety Instructions Safety Instru
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
3 Short M3000 ® System Overview M3
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
3 Short M3000 ® System Overview Li
Page 37 and 38:
3 Short M3000 ® System Overview MA
Page 39 and 40:
4 Environmental Conditions Use in S
Page 41 and 42: 5 Mechanical Installation DIN Rail
Page 49 and 50: 6 Project Planning and Installation
Page 59 and 60: 7 Networking M3000 ® Modules Ether
Page 61 and 62: 7 Networking M3000 ® Modules Profi
Page 63 and 64: 7 Networking M3000 ® Modules Profi
Page 65 and 66: 7 Networking M3000 ® Modules Seria
Page 67 and 68: 7 Networking M3000 ® Modules CAN B
Page 69 and 70: 7 Networking M3000 ® Modules CAN B
Page 71 and 72: 7 Networking M3000 ® Modules E-Bus
Page 73 and 74: 7 Networking M3000 ® Modules E-Bus
Page 75 and 76: 7 Networking M3000 ® Modules Netwo
Page 81 and 82: 8 Shutdown and Service Service 8.2
Page 83 and 84: 10 MSC II (Moog Servo Controller) P
Page 85 and 86: 10 MSC II (Moog Servo Controller) G
Page 87 and 88: 10 MSC II (Moog Servo Controller) B
Page 89 and 90: 10 MSC II (Moog Servo Controller) V
Page 91: 10 MSC II (Moog Servo Controller) V
Page 97 and 98: 10 MSC II (Moog Servo Controller) L
Page 99 and 100: 10 MSC II (Moog Servo Controller) R
Page 105 and 106: 10 MSC II (Moog Servo Controller) D
Page 119 and 120: 10 MSC II (Moog Servo Controller) E
Page 121 and 122: 10 MSC II (Moog Servo Controller) C
Page 123 and 124: 10 MSC II (Moog Servo Controller) S
Page 125 and 126: 11 Product Range M3000 ® Starter K
Page 127 and 128: 11 Product Range M3000 ® Modules 1
Page 129 and 130: 11 Product Range License Keys 11.4
Page 131 and 132: 11 Product Range Interface Cables 1
Page 133 and 134: 11 Product Range Plug-In Terminal S
Page 135 and 136: 12 Appendix Typographical Conventio
Page 137 and 138: 12 Appendix Abbreviations Abbreviat
Page 139 and 140: 12 Appendix Quoted Standards DIN EN
Page 141 and 142: 13 Index 13 Index A «A1»…«A4»
Page 143 and 144:
13 Index I Identification of M3000
Page 145 and 146:
13 Index P Packaging Original packa
Page 147 and 148:
13 Index Symbols and styles used in
show all

User Manual M3000® Automation System / MSC II (Moog Servo ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?