SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite
SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite
Color Check . . . continued7) After 10 days average the white, blue, and brown values and enter datain the designated place on the color check label.8) Enter date, illuminant, observer, aperture size, temperature, instrumentmodel, and serial number on color check label. Note: Temperature ofthe reference standard should be maintained (±2°C) throughout colorcheck sequence.Periodic Color Check Procedure1) Copy reference data located on the color check label to the shadedareas on the color check record located on the next page.2) Perform steps 1-4 in reference data procedure.3) Record the measured white, blue, and brown values and date on thecolor check record on the next page. Note: You may want to makeseveral copies of the color check record before entering any data. Thiswill allow you to have additional pages available when they are needed.4) Compare measured values to the reference values.If values are off, clean optics and reference standard and remeasure.Consistent L*, a*, or b* differences exceeding .30 (or obvious trendsaway from the reference data) may require the unit to be serviced.Contact X-Rite or authorized service center if this is the case.Always verify color performance with the same aperture size, illum/obs,and temperature.D-2
COLOR CHECK RECORDDate: Illuminant: Observer:Temperature: Aperture Size: Model-S/N:Reference White Blue BrownValues L* a* b* L* a* b* L* a* b*DateD-3
- Page 39 and 40: Using Measurement Averaging . . . c
- Page 41 and 42: Adjusting Tolerance Values . . . co
- Page 43 and 44: Adjusting Tolerance Values . . . co
- Page 45 and 46: 5.2 Pass/Fail MeasurementThe Pass/F
- Page 47 and 48: SECTION 6STORAGE OPERATIONSubjects
- Page 49 and 50: Storing Measurements . . . continue
- Page 51 and 52: Deleting Stored Measurements . . .
- Page 53 and 54: 6.3 Printing Stored MeasurementsThe
- Page 55 and 56: Printing Stored Measurements . . .
- Page 57 and 58: Tagging and Storing Operation . . .
- Page 59 and 60: Tagging and Storing Operation . . .
- Page 61 and 62: 6.5 QA-Master ‘‘Run Job’’ O
- Page 63 and 64: Setting RS-232 Communication Option
- Page 65 and 66: 7.2 Setting Operation OptionsThere
- Page 67 and 68: Setting Operation Options . . . con
- Page 69 and 70: Setting Operation Options . . . con
- Page 71 and 72: Setting Printout Options . . . cont
- Page 73 and 74: 7.4 Setting Date And TimeThe date a
- Page 75 and 76: 8.2 Cleaning the OpticsThe optics s
- Page 77 and 78: 8.4 Replacing the Target Window☛
- Page 79 and 80: 8.6 Troubleshooting TipsInstrument
- Page 81 and 82: 9.2 Scanning a Bar CodeFollow these
- Page 83 and 84: Troubleshooting . . . continuedWas
- Page 85 and 86: Technical Specifications . . . cont
- Page 87 and 88: Display Messages . . . continuedCal
- Page 89: APPENDIX - DCOLOR CHECKThe color ch
COLOR CHECK RECORDDate: Illuminant: Observer:Temperature: Aperture Size: Model-S/N:Reference White Blue BrownValues L* a* b* L* a* b* L* a* b*DateD-3