SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

More documents

Recommendations

Info

9.3 TroubleshootingThe factory default mode can be restored if the SP78-200 BCR isplaced into an unusable or unknown configuration.To restore the factory default mode:1) Disconnect the BCR from the instrument.2) Reconnect the BCR to the instrument.3) Scan the default configuration bar codes shown in your SP78-200 BarCode Reader Instruction Sheet (P/N SP78-510).Does the SP78-200 BCR have power?A red light will be visible at the tip of the BCR if it has power.Check the connection between the BCR and the instrument. Be sure theconnector is correctly inserted.Check the power supply for the instrument. Refer to the instrumentUser’s <strong>Manual</strong>, Troubleshooting section if the instrument does not havepower.Is the SP78-200 BCR configuration correct?To restore the factory default mode:1) Disconnect the BCR from the instrument.2) Reconnect the BCR to the instrument.3) Scan the default configuration bar code. See Figure 4.Does the SP78-200 BCR wavelength of light match the bar code?The BCR will not read bar codes that are designed to be secure (blackon black.) The optical signal returning from the bar code is not adequatefor measuring the bars and spaces.Is the SP78-200 BCR being held at the correct angle?The BCR will operate when held at an angle of 5° to 45°. Theoptimum operating angle is from 10° to 30°.9-3
Troubleshooting . . . continuedWas the entire bar code scanned?Drag the BCR through the entire bar code at a constant speed. Increasethe scanning speed. Typically the BCR is moved too slowly.Be sure the BCR scans the entire bar code.Be sure the BCR maintained contact with the surface of the bar code.Be sure the bar code is not damaged, dirty or worn. Try to scan an areawithout these defects.Does the SP78-200 BCR tip need replacement?If the tip becomes damaged or shows signs of excessive wear, it mustbe replaced.To replace the tip:1) Disconnect the BCR from the instrument.2) Unscrew the tip from the wand.3) Replace using part number SE124-01-01.9-4
Page 2 and 3:
WARNING: Shielded interface cables
Page 4 and 5:
Dear Customer:Congratulations! We a
Page 8 and 9:
Table of Contents . . . continued7.
Page 10 and 11:
User InterfaceThis information will
Page 12 and 13:
What To Do First . . . continuedApp
Page 14 and 15:
Packaging Illustration1-2
Page 16 and 17:
1.3 Installing the Battery PackThe
Page 18 and 19:
1.5 Charging the Battery Pack‘‘
Page 20 and 21:
1.6 Menu Page SelectionThe main men
Page 22 and 23:
SECTION 2INSTRUMENT POSITIONING &ME
Page 24:
Instrument Positioning & Measuremen
Page 27 and 28:
Positioning the Instrument on the W
Page 29 and 30:
3.3 Calibration ProcedureTo perform
Page 31 and 32: Calibration Procedure . . . continu
Page 33 and 34: 4.2 Illuminant/Observer SelectionTh
Page 35 and 36: Reference Entry . . . continued5) M
Page 37 and 38: Sample Measurement . . . continued4
Page 39 and 40: Using Measurement Averaging . . . c
Page 41 and 42: Adjusting Tolerance Values . . . co
Page 43 and 44: Adjusting Tolerance Values . . . co
Page 45 and 46: 5.2 Pass/Fail MeasurementThe Pass/F
Page 47 and 48: SECTION 6STORAGE OPERATIONSubjects
Page 49 and 50: Storing Measurements . . . continue
Page 51 and 52: Deleting Stored Measurements . . .
Page 53 and 54: 6.3 Printing Stored MeasurementsThe
Page 55 and 56: Printing Stored Measurements . . .
Page 57 and 58: Tagging and Storing Operation . . .
Page 59 and 60: Tagging and Storing Operation . . .
Page 61 and 62: 6.5 QA-Master ‘‘Run Job’’ O
Page 63 and 64: Setting RS-232 Communication Option
Page 65 and 66: 7.2 Setting Operation OptionsThere
Page 67 and 68: Setting Operation Options . . . con
Page 69 and 70: Setting Operation Options . . . con
Page 71 and 72: Setting Printout Options . . . cont
Page 73 and 74: 7.4 Setting Date And TimeThe date a
Page 75 and 76: 8.2 Cleaning the OpticsThe optics s
Page 77 and 78: 8.4 Replacing the Target Window☛
Page 79 and 80: 8.6 Troubleshooting TipsInstrument
Page 81: 9.2 Scanning a Bar CodeFollow these
Page 85 and 86: Technical Specifications . . . cont
Page 87 and 88: Display Messages . . . continuedCal
Page 89 and 90: APPENDIX - DCOLOR CHECKThe color ch
Page 91 and 92: COLOR CHECK RECORDDate: Illuminant:
show all

SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?