SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

More documents

Recommendations

Info

8.5 Reading Lamp Replacement InformationDue to the circuit complexity, critical alignment procedures, and testequipment required - The read lamp should only be replaced by X-Riteor an authorized X-Rite Service Center.The lamp is monitored for intensity, and failure warnings will bedisplayed if a problem occurs.The lamp should last approximately 500,000 measurements and iscovered by a one year limited warranty. Refer to the Limited Warrantystatement on page iii.8-5
8.6 Troubleshooting TipsInstrument will not turn On (on display):Power switch off (battery operation only).Batteries are very low and in need of charge.Contact X-Rite or Authorized Service Center.Instrument will display but not measure:Battery pack not installed.Contact X-Rite or Authorized Service Center.Incorrect measurement data continually displays:Check standard material.Calibrate instrument (see Sec. 3).Clean optics (see Sec. 8).Contact X-Rite or Authorized Service Center.Measurement drifts:Clean optics (see Sec. 8).Calibrate instrument (see Sec. 3).Contact X-Rite or Authorized Service Center.Instrument will not calibrate properly:Calibration standard needs to be cleaned (see Sec. 3).Clean optics (see Sec. 8).Contact X-Rite or Authorized Service Center.8-6
Page 2 and 3:
WARNING: Shielded interface cables
Page 4 and 5:
Dear Customer:Congratulations! We a
Page 8 and 9:
Table of Contents . . . continued7.
Page 10 and 11:
User InterfaceThis information will
Page 12 and 13:
What To Do First . . . continuedApp
Page 14 and 15:
Packaging Illustration1-2
Page 16 and 17:
1.3 Installing the Battery PackThe
Page 18 and 19:
1.5 Charging the Battery Pack‘‘
Page 20 and 21:
1.6 Menu Page SelectionThe main men
Page 22 and 23:
SECTION 2INSTRUMENT POSITIONING &ME
Page 24:
Instrument Positioning & Measuremen
Page 27 and 28: Positioning the Instrument on the W
Page 29 and 30: 3.3 Calibration ProcedureTo perform
Page 31 and 32: Calibration Procedure . . . continu
Page 33 and 34: 4.2 Illuminant/Observer SelectionTh
Page 35 and 36: Reference Entry . . . continued5) M
Page 37 and 38: Sample Measurement . . . continued4
Page 39 and 40: Using Measurement Averaging . . . c
Page 41 and 42: Adjusting Tolerance Values . . . co
Page 43 and 44: Adjusting Tolerance Values . . . co
Page 45 and 46: 5.2 Pass/Fail MeasurementThe Pass/F
Page 47 and 48: SECTION 6STORAGE OPERATIONSubjects
Page 49 and 50: Storing Measurements . . . continue
Page 51 and 52: Deleting Stored Measurements . . .
Page 53 and 54: 6.3 Printing Stored MeasurementsThe
Page 55 and 56: Printing Stored Measurements . . .
Page 57 and 58: Tagging and Storing Operation . . .
Page 59 and 60: Tagging and Storing Operation . . .
Page 61 and 62: 6.5 QA-Master ‘‘Run Job’’ O
Page 63 and 64: Setting RS-232 Communication Option
Page 65 and 66: 7.2 Setting Operation OptionsThere
Page 67 and 68: Setting Operation Options . . . con
Page 69 and 70: Setting Operation Options . . . con
Page 71 and 72: Setting Printout Options . . . cont
Page 73 and 74: 7.4 Setting Date And TimeThe date a
Page 75 and 76: 8.2 Cleaning the OpticsThe optics s
Page 77: 8.4 Replacing the Target Window☛
Page 81 and 82: 9.2 Scanning a Bar CodeFollow these
Page 83 and 84: Troubleshooting . . . continuedWas
Page 85 and 86: Technical Specifications . . . cont
Page 87 and 88: Display Messages . . . continuedCal
Page 89 and 90: APPENDIX - DCOLOR CHECKThe color ch
Page 91 and 92: COLOR CHECK RECORDDate: Illuminant:
show all

SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?