SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

More documents

Recommendations

Info

Adjusting Tolerance Values . . . continuedPASS/FAIL METHOD = ∆ECMC5) Press [tol] key #4 to advance to‘‘PASS/FAIL LIMITS’’ screen.DEFINE TOLERANCEFOR REF01exit Ecmc D65 10tolKey#1 Key#2 Key#3 Key#46) Set tolerance values by pressingthe [next] key #4 to move cursorto desired ‘‘cf’’, ‘‘l’’, & ‘‘c’’attribute. Press [+] key #2 toincrease value or [--] key #3 todecrease value.- Press [exit] key #1 twice to saveand exit tolerance procedure.PASS/FAIL LIMITS =cf l c1.00 1.00 1.00exit +_nextKey#1 Key#2 Key#3 Key#4PressTwiceTo ExitIncrease Decrease Move Cursor5-5
5.2 Pass/Fail MeasurementThe Pass/Fail measurement will indicate a pass or fail signal based onthe tolerance limits set on the selected reference.When the SP88/SP98 is interfaced to a serial printer, data will printafter each measurement. The data that is printed is based on the PrintoutOptions selected (see Section 7.3).If measurement data storage with pass/fail indication is required, referto Section 6.To take a pass/fail measurement:☛ References must be measured and tolerances edited before a pass/fail measurement will displayusable data. Refer to Sections 4.3 and 5.1.1) Press [pass/fail] key #3 at theMENU PAGE 1 level to enterpass/fail function.menupg2MENU PAGE 1passnorm fail storeKey#1 Key#2 Key#3 Key#4Press2) The Pass/Fail measurement screenis displayed.☛ A reference must be selected if ‘‘Auto Reference ’’is disabled in Operation Options. Press the[ref#] key #4 to access reference menu.L* -.02a* .00b* -.01menuPASSE .02tol ref01Key#1 Key#2 Key#3 Key#4Select ForManual Ref3) Take measurement by loweringunit to sample.5-6➩
Page 2 and 3: WARNING: Shielded interface cables
Page 4 and 5: Dear Customer:Congratulations! We a
Page 8 and 9: Table of Contents . . . continued7.
Page 10 and 11: User InterfaceThis information will
Page 12 and 13: What To Do First . . . continuedApp
Page 14 and 15: Packaging Illustration1-2
Page 16 and 17: 1.3 Installing the Battery PackThe
Page 18 and 19: 1.5 Charging the Battery Pack‘‘
Page 20 and 21: 1.6 Menu Page SelectionThe main men
Page 22 and 23: SECTION 2INSTRUMENT POSITIONING &ME
Page 24: Instrument Positioning & Measuremen
Page 27 and 28: Positioning the Instrument on the W
Page 29 and 30: 3.3 Calibration ProcedureTo perform
Page 31 and 32: Calibration Procedure . . . continu
Page 33 and 34: 4.2 Illuminant/Observer SelectionTh
Page 35 and 36: Reference Entry . . . continued5) M
Page 37 and 38: Sample Measurement . . . continued4
Page 39 and 40: Using Measurement Averaging . . . c
Page 41 and 42: Adjusting Tolerance Values . . . co
Page 43: Adjusting Tolerance Values . . . co
Page 47 and 48: SECTION 6STORAGE OPERATIONSubjects
Page 49 and 50: Storing Measurements . . . continue
Page 51 and 52: Deleting Stored Measurements . . .
Page 53 and 54: 6.3 Printing Stored MeasurementsThe
Page 55 and 56: Printing Stored Measurements . . .
Page 57 and 58: Tagging and Storing Operation . . .
Page 59 and 60: Tagging and Storing Operation . . .
Page 61 and 62: 6.5 QA-Master ‘‘Run Job’’ O
Page 63 and 64: Setting RS-232 Communication Option
Page 65 and 66: 7.2 Setting Operation OptionsThere
Page 67 and 68: Setting Operation Options . . . con
Page 69 and 70: Setting Operation Options . . . con
Page 71 and 72: Setting Printout Options . . . cont
Page 73 and 74: 7.4 Setting Date And TimeThe date a
Page 75 and 76: 8.2 Cleaning the OpticsThe optics s
Page 77 and 78: 8.4 Replacing the Target Window☛
Page 79 and 80: 8.6 Troubleshooting TipsInstrument
Page 81 and 82: 9.2 Scanning a Bar CodeFollow these
Page 83 and 84: Troubleshooting . . . continuedWas
Page 85 and 86: Technical Specifications . . . cont
Page 87 and 88: Display Messages . . . continuedCal
Page 89 and 90: APPENDIX - DCOLOR CHECKThe color ch
Page 91 and 92: COLOR CHECK RECORDDate: Illuminant:

SP88/SP98 Spectrophotometer Operating Manual ... - X-Rite

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?