Amphenol Heavy Duty Cylindrical Connectors

More documents

Recommendations

Info

MIL-C-22992, Class Linstallation instructionsMS90557 Connector9 8 7 6 5Cable Connecting ReceptacleComponents:1. Shell2. Insert Assembly, Socket3. Contact, Socket4. Spacer Assembly, Socket5. Back Adapter6. Gland Washer7. Gland8. Cable Grip9. Gland Nut10. Lockwasher (3 each)11. Screw (3 each)12. Protective Cap Assembly (Not shown)11 104 3 2 1Note: On shell size 32 connectors, item #6 (Gland Washer) is contained within item #5 (Back Adaper).MS90558 Connector2Wall Mount Plug Components:1. Shell and Coupling Nut Assembly2. Insert Assembly, Pin3. Contact, Pin4. Grommet Assembly, Pin5. Nut, Retaining6. Protective Cap Assembly (Not Shown)7. Flange Gasket (Not Shown)5 4 3 118
MIL-C-22992, Class Linstallation instructionsContact InstallationStep 1) Insert stripped conductors in contact wirewells.If contact bushing is used, insert conductor in bushingand bushing in contact wirewell. If two or more groundwires are inserted into a single contact, make sure allwires are fully seated in wirewell.Step 2) Select correct crimping tool, locater and diecombination from the table for contacts to be installed.With conductor or contact bushing in place, insert contactinto tool. Close crimping die fully to form a uniform crimp.ContactPartNumberM39029/48-327M39029/49-335M39029/48-328M39029/48-323M39029/49-333M39029/48-324M39029/48-320M39029/49-331M39029/48-321M39029/48-322M39029/49-332M39029/48-317M39029/49-329M39029/48-318M39029/48-319M39029/49-330Size Type CrimpingTool*4/04/04/0N1/01/01/0N444N4G4G666N6G6GPSPPSPPSPPSPSPPSPico Model400B or400B-1Pico Model400B or400B-1Pico Model400B or400B-1Pico Model400B or400B-1* Available from Pico Crimping Tools Co.,9832 Jersey Ave.Santa Fe Springs, CA 90670Phone: 805-388-5510Locator*Die*RemovalTool4297-1 414DA-4/0N-1 MS90562-14297-3 414DA-1/0N MS90562-34297-5 414DA-4N MS90562-54297-6 414DA-6N MS90562-6If crimping tools are available, contacts may be affixed toconductors by soldering. Use rosin-alcohol solder flux, agood grade of 60/40 solder and a 500 watt soldering ironor probe type resistance soldering equipment. Pre-tinconductors before soldering. Solder must not be presenton shoulder or retention area of contact.Connector AssemblyStep 1) If inserts are not already positioned in the connectorshell, align large tab on insert with large slot inshell and push insert in until it bottoms in shell.Step 2) Apply a thin coating of Dow Corning DC-4 lubricantto the periphery of contact holes in spacer or grommetassembly. Push contacts into rear of spacer orgrommet assembly until locked into contact retainerbushing.Step 3) Align contacts with proper holes in insert. Smallkey of insert must be aligned with appropriate keyway inspacer or grommet assembly. Slide contacts into insertholes until spacer or grommet assembly butts againstinsert. A thin film of Dow Corning DC-4 lubricant appliedto the periphery of insert contact holes will provide maximumsealing efficiency.Step 4) Assemble accessories to connector. The backadapter “O” ring should have a very thin film of DowCorning DC-4 lubricant applied. Outer surfaces only ofgland should be lubricated with a thin film of UniTempGrease EP. Avoid getting grease on inside surfaces ofgland and on cable jacket.Step 5) Tighten retaining nut or gland nut on shell oradapter. A metal-to-metal seating condition is desireable,but may not be attainable with maximum cable diameters.Contact RemovalStep 1) Loosen all rear accessories and slide back alongcable.Step 2) Remove spacer or grommet assembly with contactsfrom connector insert.Step 3) Using the appropriate size contact removal tool,push tool over front of contact until it bottoms in spacer orgrommet assembly hole. This will open contact retainingbushing and allow contact to be removed from the spaceror grommet assembly from the rear. When using jacketedcable, all contacts should be released from contact retentionbushings before removal from spacer or grommetassembly is accomplished.19
Page 1 and 2: ®Amphenol Heavy DutyCylindrical Co
Page 4 and 5: This catalog covers Amphenol ® Hea
Page 8 and 9: MIL-C-22992, Class Lhow to orderCon
Page 10 and 11: MIL-C-22992, Class Lcontact arrange
Page 12 and 13: MIL-C-22992, Class LMS90555wall mou
Page 14 and 15: MIL-C-22992, Class LMS90557cable co
Page 16: MIL-C-22992, Class L Accessoriescon
Page 19 and 20: MIL-C-22992, Class L Accessoriespro
Page 21: MIL-C-22992, Class Linstallation in
Page 27 and 28: MIL-C-22992, QWLDinsert arrangement
Page 29 and 30: QWLDspecial insert arrangementsInse
Page 31 and 32: MIL-C-22992, QWLDcontact arrangemen
Page 43 and 44: QWLDspecial arrangementsEver expand
Page 45 and 46: QWLDspecial arrangementsfront face
Page 53 and 54: QWLDthermocouple arrangementsShell
Page 55 and 56: QWLDthermocouple arrangementsShell
Page 57 and 58: MIL-C-22992, QWLDMS17343 or 10-1940
Page 61 and 62: QWLD10-1944XXthru bulkhead receptac
Page 65 and 66: MIL-C-22992, QWLD AccessoriesM85049
Page 73 and 74:
MIL-C-22992, QWLD Accessories10-350
Page 75 and 76:
MIL-C-22992, QWLD Accessoriesprotec
Page 77 and 78:
QWLD Accessoriesencapsulation adapt
Page 79 and 80:
MIL-C-22992, QWLDMS solder contacts
Page 81 and 82:
QWLDapplication toolsComplete insta
show all

Amphenol Heavy Duty Cylindrical Connectors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?