Amphenol Heavy Duty Cylindrical Connectors

More documents

Recommendations

Info

MIL-C-22992, Class Linstallation instructionsComplete installation instructions (L-1014) for Class L connectors are available onrequest. Reproduced below are condensed assembly instructions to familiarize theuser with the installation procedure and tooling required.Cable Preparation (MS90556 and MS90557 connectors only)The following table shows the standard wire color coding, generator terminal markings,and connector contact identification used with Class L connectors.Standardized Generator Wiring and ConnectionsGeneratorTerminal Marking+ (POS)– (NEG) groundL 1L 2L 3L 0G (or Gnd)Current28Vdc28VdcACACACACACContactDesignationANABCNGConductorCircuitPositiveNegativePhase APhase BPhase CNeutralSafety groundingWire ColorBlackWhiteBlackRedBlue (Commercial may be orange)WhiteGreen (Commercial may be bare)Step 1) Determine cable lay to facilitate alignment of contacts and insert holeswithout wire crossing.Step 2) Strip cable jacket to dimension shown. Avoid cutting or nicking individualconductor insulation.ConnectorSizeDInchesApprox.28 3.00032 3.00044 4.25052 5.000OUTERJACKETNoteSome insert arrangements require that two or more ground wires be terminatedinto one contact. Dimension D must therefore be increased to permitrouting these wires around the larger conductors.DSEENOTEStep 3) Install connector components in the order shown in the applicable assemblyview illustrated on pages17 and 18.Step 4) Strip insulation of individual conductors to 3/4 inch from end of conductor.16
MIL-C-22992, Class Linstallation instructionsMS90555 Connector2 1Wall Mount Receptacle Components:1. Shell2. Insert Assembly, Socket3. Contact, Socket4. Grommet Assembly, Socket5. Nut, Retaining6. Protective Cap Assembly (Not Shown)7. Flange Gasket (Not Shown)5 4 3MS90556 ConnectorStraight Plug Components:1. Shell and Coupling Nut Assembly2. Insert Assembly, Pin3. Contact, Pin4. Spacer Assembly, Pin5. Back Adapter6. Gland Washer7. Gland8. Cable Grip9. Gland Nut10. Lockwasher (3 each)11. Screw (3 each)12. Protective Cap Assembly (Not Shown)Note: On shell size 32 connectors, item #6 (Gland Washer) is contained within item #5 (Back Adaper).17
Page 1 and 2: ®Amphenol Heavy DutyCylindrical Co
Page 4 and 5: This catalog covers Amphenol ® Hea
Page 8 and 9: MIL-C-22992, Class Lhow to orderCon
Page 10 and 11: MIL-C-22992, Class Lcontact arrange
Page 12 and 13: MIL-C-22992, Class LMS90555wall mou
Page 14 and 15: MIL-C-22992, Class LMS90557cable co
Page 16: MIL-C-22992, Class L Accessoriescon
Page 19: MIL-C-22992, Class L Accessoriespro
Page 23 and 24: MIL-C-22992, Class Linstallation in
Page 27 and 28: MIL-C-22992, QWLDinsert arrangement
Page 29 and 30: QWLDspecial insert arrangementsInse
Page 31 and 32: MIL-C-22992, QWLDcontact arrangemen
Page 43 and 44: QWLDspecial arrangementsEver expand
Page 45 and 46: QWLDspecial arrangementsfront face
Page 53 and 54: QWLDthermocouple arrangementsShell
Page 55 and 56: QWLDthermocouple arrangementsShell
Page 57 and 58: MIL-C-22992, QWLDMS17343 or 10-1940
Page 61 and 62: QWLD10-1944XXthru bulkhead receptac
Page 65 and 66: MIL-C-22992, QWLD AccessoriesM85049
Page 71 and 72:
MIL-C-22992, QWLD AccessoriesM85049
Page 73 and 74:
MIL-C-22992, QWLD Accessories10-350
Page 75 and 76:
MIL-C-22992, QWLD Accessoriesprotec
Page 77 and 78:
QWLD Accessoriesencapsulation adapt
Page 79 and 80:
MIL-C-22992, QWLDMS solder contacts
Page 81 and 82:
QWLDapplication toolsComplete insta
show all

Amphenol Heavy Duty Cylindrical Connectors

Create successful ePaper yourself

Delete template?

Save as template?