Operating Instructions 150 000 019 00 EN

More documents

Recommendations

Info

6. Starting up after winter storageWipe off the grease and oil used for conservation.Carry out all the activities described in the chapter on maintenance.Carefully read through the operating manual again.6.1 Vent Overload Coupling on the PTOShaft2(friction clutch only)Following extended downtimes, overload couplingsurfaces (2) may stick to the contact surfaces. Ventthe overload coupling before use.• Tighten the nuts (1) crosswise.• Turn the PTO shaft manually.• Undo the nuts crosswise.11KR-0-15130
7. Special accessories7.1 Night swathing gearboxThe rotary tedder can be equipped with a nightswathing gearbox.The following parts are supplied:- Night swathing gearbox (1) (maintenance-free due topermanent grease filling)- Two angle brackets (2)- Protecting pot (3)- Clamp fitting (4)- Four bolts with nuts and washers1342KW-0-027To mount the night swathing gearbox (1), dismantle thePTO shaft from the rotary tedder drive (cf. chapter 2.2"Preparations on the tractor and rotary tedder"). Fitthe protecting pot (3) and fix with the clamp fitting (4).1On the KW 7.70 and KW 8.80, the existingPTO shaft guard must be dismantled.Fix the angled bracket (2) to the designed holes withbolts (5) and nuts on the left and right side of the carrierbar.423On the KW 5.50, fit the angled brackets insuch a way that the short bevelledsurface points forwards. This is wherethe night swathing gearbox is bolted.Push the night swathing gearbox onto the PTO shaftstup of the rotary tedder and bolt it to the angledbrackets.2KW-0-028In case of the types KW 5.50 and KW 6.70, shorten theguard of the pto drive shaft(a = max. 80 mm).Check PTO shaft length!aKW-1-<strong>00</strong>131
Page 1 and 2: Rotary tedderKW 5.50 / 4 x 7KW 6.70
Page 3 and 4: I. ForewordDear customer,Ordering R
Page 5 and 6: III. General1. Operation in Accorda
Page 7 and 8: 5. Hydraulic System1. The hydraulic
Page 9 and 10: 1Do not exceed themaximum permitted
Page 11 and 12: 1440 135-3 (1x) bei KW 5.50939 429-
Page 13 and 14: 2. Preparations for use2.1. Special
Page 15 and 16: PTO shaftAfter the rotary tedder ha
Page 17 and 18: 2.4 Adjusting the PTO shaft length
Page 19 and 20: 2.7 Conversion from working totrans
Page 21 and 22: Switch off the engine and remove th
Page 23 and 24: 3.3 Drive rpmsWide spreading (teddi
Page 25 and 26: 3.7 Tine adjustmentThe tines (3) mu
Page 27 and 28: 4.3 HydraulicsThe rotary tedder has
Page 29 and 30: Lubrication points on the KW 6.70 /
Page 31: 5. Winter storage5.1 Safety instruc
Page 35 and 36: 7.3 Wheel guards• For all service
Page 37: 7.4 Fixed lightingA permanently fix
Page 40 and 41: 1. Special safety instructions• P
Page 42 and 43: 4. Mounting the disc arms to the di
Page 44 and 45: Bolt the front protective frame (2)
Page 46 and 47: 5.3 Mounting of the protective fram
Page 48: KW 6.70/6, KW 7.70/6x7 and KW 8.80/

Operating Instructions 150 000 019 00 EN

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?