Operating Instructions 150 000 019 00 EN

More documents

Recommendations

Info

Lubrication points on the KW 8.80 / 8For reasons of clarity, the lubrication points have been shown on only one side of the rotary tedder. On the otherside, there are lubrication nipples at exactly the same points (as a mirror image).50h50h10h50h10h50h50h10h10 hKW-4-<strong>00</strong>228
5. Winter storage5.1 Safety instructions• Repair, service, maintenance and cleaning work must only be carried outwhen the machine is at a standstill.• Switch off the engine and remove the ignition key.• After service and maintenance work has been completed, all protectivepanels and other protective devices must be correctly fitted again.• Avoid skin contact with oil, grease, cleansing agents and solvents.• In the event of injury or cauterization caused by oil, cleansing agent orsolvents, consult a doctor immediately.5.2 GeneralThoroughly clean the rotary tedder before placing it in winter storage. If a high-pressure water cleaner is used, donot aim the water jet directly at the bearings. After cleaning, grease all lubrication nipples. Do not wipe off greasethat oozes out of the lubrication points. The grease ring provides additional protection from moisture.Check all moving parts for freedom of movement. Where appropriate, dismantle and clean them, then lubricatethem and fit them again. If necessary, replace with new parts. Only use original KRONE replacement parts.Pull the PTO shaft apart. Lubricate the inner tubes and the protective tubes with grease. Grease the lubricationnipples on the universal joint and the bearing rings of the protective tubes.Store the rotary tedder in a dry place, and not near artificial fertilizers or stables.Touch up paintwork. Bare metal must be thoroughly preserved with anti-corrosion agent.The rotary tedder must only be jacked up with a suitable jack. Make sure thatthe rotary tedder is solidly supported when it is jacked up.To lift the tyres (the tyres can be damaged if the rotary tedder stands on the same spot for a long period),jack the rotary tedder up on a support stand. Protect the tyres from outside factors such as oil, grease, directsunlight etc.Have necessary repair work carried out in the period directly after the harvest season. Make up a collective list ofall replacement parts required. This will make it easier for your KRONE dealer to deal with your orders, and it willgive you the security of knowing that your machine will be fully operational at the beginning of the new season.29
Page 1 and 2: Rotary tedderKW 5.50 / 4 x 7KW 6.70
Page 3 and 4: I. ForewordDear customer,Ordering R
Page 5 and 6: III. General1. Operation in Accorda
Page 7 and 8: 5. Hydraulic System1. The hydraulic
Page 9 and 10: 1Do not exceed themaximum permitted
Page 11 and 12: 1440 135-3 (1x) bei KW 5.50939 429-
Page 13 and 14: 2. Preparations for use2.1. Special
Page 15 and 16: PTO shaftAfter the rotary tedder ha
Page 17 and 18: 2.4 Adjusting the PTO shaft length
Page 19 and 20: 2.7 Conversion from working totrans
Page 21 and 22: Switch off the engine and remove th
Page 23 and 24: 3.3 Drive rpmsWide spreading (teddi
Page 25 and 26: 3.7 Tine adjustmentThe tines (3) mu
Page 27 and 28: 4.3 HydraulicsThe rotary tedder has
Page 29: Lubrication points on the KW 6.70 /
Page 33 and 34: 7. Special accessories7.1 Night swa
Page 35 and 36: 7.3 Wheel guards• For all service
Page 37: 7.4 Fixed lightingA permanently fix
Page 40 and 41: 1. Special safety instructions• P
Page 42 and 43: 4. Mounting the disc arms to the di
Page 44 and 45: Bolt the front protective frame (2)
Page 46 and 47: 5.3 Mounting of the protective fram
Page 48: KW 6.70/6, KW 7.70/6x7 and KW 8.80/

Operating Instructions 150 000 019 00 EN

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?