ATV61 LON WORK - error

More documents

Recommendations

Info

11. Network variables and configuration properties11. 10. Emergencyb Emergency command (nviEmergOverride)This variable produces an emergency stop of the drive.The emergency state disappears after the trip has been released by nviEmergOverride with value 0.Then it is possible to reset the drive by nviResetFault or a local command.NameSNVT referenceSNVT index 103nviEmergOverrideSNVT_hvac_emergValue Action Comment0 Drive trip release EMERG_NORMAL (No Emergency mode)1 Emergency stop EMERG_PRESSURIZE (Emergency pressurize mode)2 EMERG_DEPRESSURIZE (Emergency depressurize mode)3 EMERG_ PURGE (Emergency purge mode)4 EMERG_SHUTDOWN (Emergency shutdown mode)5 EMERG_FIRE6 ... 0xFF ...Emergency stop produces a fault [External fault com.] (EPF2).The reaction of the drive can be configured by the parameter [External fault mgt] (EPL). This parameter is located in the menu [1.8 FAULTMANAGEMENT] (FLt), sub-menu [EXTERNAL FAULT] (EtF-).b Emergency status (nvoEmergStatus)This variable monitors the emergency status of the drive.NameSNVT referenceSNVT index 103nvoEmergStatusSNVT_hvac_emergValue Action Comment0 No emergency stop EMERG_NORMAL (No Emergency mode)1 Emergency stop EMERG_PRESSURIZE (Emergency pressurize mode)2 EMERG_DEPRESSURIZE (Emergency depressurize mode)3 EMERG_ PURGE (Emergency purge mode)4 EMERG_SHUTDOWN (Emergency shutdown mode)5 EMERG_FIRE6 ... 0xFF ...45
11. Network variables and configuration properties11. 11. Adjustmentb Maximum Motor Speed (nciMaxSpeed)This configuration property is used to define the maximum speed of the motor.The value is entered as a percent of nominal speed in RPM, as defined by the Nominal Speed (nciNmlSpeed) configuration value. Thevalue of the maximum speed must be validated against the value of the minimum speed as follows:-163.840 y minimum speed y maximum speed y 163 830NameSCPT referenceSCPT index 50SNVT referenceSNVT index 81nciMaxSpeedUnit 0.005%SCPTmaxSetpointSNVT_lev_percentRange -163 840% ... 163 830%163 835% = 32 767 = 0x7FFF: invalidDefault value 100 000%DefinitionMaximum Motor SpeedThis network variable is not linked to the drive parameter [High speed] (HSP).See note on next page.b Minimum Motor Speed (nciMinSpeed)This configuration property is used to define the minimum speed of the motor.The value is entered as a percent of nominal speed in RPM, as defined by the Nominal Speed (nciNmlSpeed) configuration value. Thevalue of the minimum speed must be validated against the value of the maximum speed as follows:-163 840 y minimum speed y maximum speed y 163 830NameSCPT referenceSCPT index 53SNVT referenceSNVT index 81nciMinSpeedUnit 0.005%SCPTminSetpointSNVT_lev_percentRange -163 840% ... 163 830%163 835% = 32 767 = 0x7FFF: invalidDefault value 0.000%DefinitionMinimum Motor SpeedThis network variable is not linked to the drive parameter [Low speed] (LSP).See note on next page.46
Page 6: 2. Before you beginRead and underst
Page 10 and 11: 6. Hardware setup6. 1. Receipt• C
Page 12 and 13: 7. Connecting to the bus7. 2. Cable
Page 14 and 15: 8. Configuration8. 1. Service pinTh
Page 16 and 17: 8. ConfigurationSwitching of contro
Page 18 and 19: 8. Configurationb Control via LonWo
Page 20 and 21: 8. ConfigurationControl via LonWork
Page 22 and 23: 8. Configuration8. 4. Communication
Page 24 and 25: 9. Diagnostics9. 1. LEDs of the car
Page 26 and 27: 9. Diagnostics9. 3. Communication s
Page 28 and 29: 10. Functional profileb Objects sup
Page 30 and 31: 11. Network variables and configura
Page 36 and 37: Network variables and configuration

ATV61 LON WORK - error

Create successful ePaper yourself

Delete template?

Save as template?