Specalog for 994F Wheel Loader, AEHQ5640-01 - Teknoxgroup

Buckets and Ground Engaging ToolsCat buckets provide the flexibility to match the machine to the material and conditions.High Productivity. Aggressive Catbucket designs deliver unmatchedproductivity in the most demandingapplications. 994F buckets have beenredesigned for optimal loadability andstructural reliability.Rugged Design. Cat buckets aremanufactured using shell-tineconstruction to resist twisting anddistortion. A more aggressive spadeedge increases bucket penetration andfill factors and provides better retentionof loose material. An integral rockguard helps retain big loads for greaterfill factors and optimum truck loading.Spade Edge Rock Buckets. Spade edgerock buckets with bolt-on segments aredesigned to penetrate through the pilewhile leaving a smooth work floor.Shouldered, double-strap adapters alloweasy change-out and bolt-on segmentsextend base edge life.Serrated Edge Coal Bucket.Serrated edge bucket is recommendedfor low abrasion material loadingwhere greater penetration is required.It does not use GET, thus eliminatingthe risk of iron falling into crushers.Replaceable serrated or straight edgeis available if needed. Serrated edgeis standard for the 36 m 3 (47 yd 3 ) coalbucket, but can be added to the smallerbuckets upon request.Bucket Protection. Cat Ground EngagingTools (G.E.T.) provide superior bucketprotection for long life in the mostpunishing conditions. Built to absorbshock, impact, and abrasion, G.E.T.work and wear as a system to boostproductivity and lower costs.Tips. Tips extend bucket life in highwear applications.Sidebar Protectors. Protects bucketcorner and sides from wear in abrasivematerials. Pin-on sidebars are reversibleto extend wear life.Edge Protectors. Protects bucket edgefrom wear in materials with high wearrates. Independently pinned for easyreplacement without removing tipsor adapters.Wear Plates. Replaceable wear platesprotect the bucket bottom. Bolt-on andweld-on wear plates protect the rearbase edge from damage.Tips. Tips extend bucket life in highwear applications.Sidebar Protectors. Protects bucketcorner and sides from wear in abrasivematerials. Pin-on sidebars are reversibleto extend wear life.Edge Protectors. Protects bucket edgefrom wear in materials with high wearrates. Independently pinned for easyreplacement without removing tipsor adapters.Wear Plates. Replaceable wear platesprotect the bucket bottom. Bolt-on andweld-on wear plates protect the rearbase edge from damage.9

Operator’s StationErgonomically designed for operator comfort, superior control and high productivity.10

Spacious Cab Design. The 994F sets thestandard for productivity with advancedcontrols and greater operator comfort.Features include outstanding visibility,excellent cab ventilation, interior soundlevels below 75 dBA, trainer seat, cupholder, storage bin, radio ready andmore. Improvements made for increasedoperator maneuverability and productivity.Steering and Transmission IntegratedControl System (STIC). Combinesdirectional selection, gear selection andsteering into a single lever for maximumresponsiveness. Simple side-to-sidemotion turns machine right or left.Transmission shifting (forward/neutral/reverse) is controlled by the operator’sfingers, and gear selection is controlledby the thumb. The integrated controlsystem delivers low effort controls forsmoother, faster cycles with lessoperator fatigue.Left Brake Pedal. Allows the impellerclutch torque converter to modulaterimpull from 100% to 25%. After 25%is achieved, the brakes are engagedfor improved control and smootherdirectional shifts. This improves speedcontrol when approaching the truck.Cat Comfort Series Seat. With airsuspension and retractable seat beltis designed for comfort and support.Seat cushions reduce pressure on thelower back and thighs while allowingunrestricted arm and leg movement.The seat is six-way adjustable and theretractable seat belt remains off thefloor and is easy to reach for the operator.Armrests are height and tilt adjustable.Trainer seat. The trainer seat consistsof a padded seat and back with lap styleseat belt. When the trainer seat is not inuse, the back can be folded down andused as a drink tray and there is a storagecompartment (room for a large lunchcooler) under the seat.Seat Mounted Pilot Hydraulic Controlsand Armrests. Provide low effort, controlfor enhanced comfort and stability.Controls and arm rests are fore, aftand height adjustable to accommodateoperators of any size in a comfortableoperating position. The levers areergonomically designed for improvedoperator comfort.Vital Information Management System.VIMS system is the standard displaysystem that provides information onthe machine’s major components andsystems. Gauge displays fuel tank leveland temperatures for engine coolant,power train and hydraulic oil. Tachometeris an analog gauge with digital readoutfor gear selection. The Payload ControlSystem is included in VIMS system.Automatic Kickouts. Lift, lower andbucket tilt automatic kickouts areadjustable electronically from the cab.Throttle Lock. Allows the operatorto preset the engine speed, resultingin faster cycle times and increasedproductivity.Rimpull Control System (RCS). Allowsoperator to match rimpull settings tojob conditions with four-position dial.Operator can adjust maximum rimpullfrom 100% down to 90, 85, 75 and 65%while in first gear. Matching rimpull tojob conditions provides greater tractionin slippery or rough conditions forbetter performance and longer tire life.Rimpull Control System Switch.Turns RCS on and off.Other Features.• outstanding viewing area• excellent cab ventilation• interior sound levels below 75 dB(A)• standard coat hook• intermittent wet-arm wipers(front and rear)• radio-ready• CAES ready• rear vision camera ready• Product Link ready• VIMS wireless ready11

Matched SystemsAn efficient loading/hauling system starts with a perfect match.994F Standard LiftPass Match785C 4994F High LiftPass Match789C 6994F Super-High LiftPass Match789C Coal body 6789C 5 793C 7 793C Coal body 7Application Match. The standard 994Fis sized to load the 150-ton 785C infour passes. The 994F high-lift loadsthe 195-ton 789C in six passes andthe 240-ton 793C in seven passes.The 994F Super High-Lift loads the195 ton 789C coal body in six passesand the 240 ton 793C coal body inseven passes.Efficient Combination. For full truckpayloads with minimum loading time,an efficient loading/hauling systemstarts with a perfect match. Cat WheelLoaders are matched with Cat C-SeriesMining Trucks to maximize volume ofmaterial moved at the lowest operatingcost-per-ton.Bucket Selection. Selection of the rightbucket width depends on penetrationrequirements and the loading target.Bucket sizes are matched to truck bedcapacities for optimum loading efficiencyand greater productivity.Narrow Bucket. The narrower 5650 mm(222 in) buckets are optimally matchedto load the Cat 785C, and are also sizedfor the 789C.Wide Bucket. The wider 6220 mm(244 in) buckets are optimally matchedto load the larger Cat 789C, and are alsosized for the 793C.16

SafetyCaterpillar mining machines and systems are designed with safety as their first priority.Product Safety. Caterpillar has been andcontinues to be proactive in developingmining machines that meet or exceedsafety standards. Safety is an integralpart of all machine and systems designs.SAE and ISO Standards. The 994F isdesigned to national and internationalstandards, and has been tested andself certified to comply with applicableSAE and ISO safety standards.Integral ROPS/FOPS Cab. Mounted tothe main frame to provide rollover andfalling object protection. ROPS structureis designed as an extension of theloader frame.Ladder/Secondary Egress. Two wide,stationary stairways with handrails onboth sides allow three-point contactaccess to and from the machine.Brake Systems. Four corner oil-cooledbraking system provides excellent controlin slippery conditions. The service brakesare actuated by modulated hydraulicpressure, while secondary and parkingbrake functions are spring applied andhydraulic released. This system assuresbraking in the event of completehydraulic failure.Steering System. A twin double-actingcylinder steering system is designed todeliver precise control under all loadingand underfoot conditions. The steeringhydraulic system is separate from themain hydraulic system to prevent crosscontaminationand overheating fromother sources.Supplemental Steering System.Provided using a ground driven pump isstandard on the 994F. Backup steeringsystem allows the operator to maintaincontrol of the loader in the event of afailure in the main steering system.Rear Vision Camera (optional). Locatedon top of the radiator in the center.Provides the operator 115° of fieldvision via a colored monitor located inthe cab. Enables operator to see directlybehind the loader.Trainer Seat. The trainer seat makestraining new operators in the correctoperation of the loader easier. In additionobserving operational issues is easier.Lock-out Panel. The panel is convenientlylocated on the left-hand side bumper infront of the ladder allowing the operator/serviceman to reach the switches fromground level. In addition to the shutoffand lockout switches described below,this panel contains a VIMS port, stairwaylights and hood lights switches.Engine Shutoff Switch. An engineshutoff switch is located in the rearground level lockout panel forimmediate shutdown.Transmission Lockout. A transmissionlockout switch is located in the rearground level lockout panel. Enables tolockout machine transmission to preventgear engagement while the operator isnot in the cab.Starter Lockout. A starter lockoutswitch, when enabled, prevents thestarter from being activated whileservice is being performed.Toe Kicks. Toe kicks have been addedto the rear platform. Prevents tools fromfalling off while servicing the machine.Electrical System Disconnect. A batterydisconnect switch, which is convenientlylocated near the left stairs, provideslockout of the electrical system forservice work.Service Center. Located at ground levelallowing easy access for filling anddraining machine fluid compartments.Payload Policy. Safety is integral tomaintaining the highest productivity inmining machine operation. Caterpillar’s10/10 Payload Policy assures thatsteering and braking systems havesufficient capacity to perform at a10% overload. VIMS, which is standardon the 994F, includes a payload indicatorsystem. VIMS notifies the operatorwhen the bucket is overloaded.Standard Safety Features.• Slip resistant surfaces• Retractable, 75 mm (3 in) wideseat belts• Wide-angle mirrors• Hand rails• Low interior sound level• Trainer seat17

EngineEngine ModelCat ® 3516B HD EUIRated Speed1,600 rpmGross Power – SAE J1995 1176 kW 1,577 hpNet Power – EEC 80/1269 1092 kW 1,463 hpNet Power – ISO 9249 1092 kW 1,463 hpNet Power – SAE J1349 1180 kW 1,447 hpBore 170 mm 6.7 inStroke 215 mm 8.5 inDisplacement 78 L 4,875 in 3Peak Torque @ 1,100 rpm 8499 N•m 6,289 lb ftTorque Rise 32%• Net power advertised is the power available at the flywheelwhen the engine is equipped with fan, air cleaner, muffler,and alternator.• Net torque rise meets SAE J139.• No engine derating required up to 3050 m (10,000 ft) altitude.Operating SpecificationsOperating Weight 195 434 kg 430,858 lbRated Payload – Standard 35 tonnes 38 tonsRated Payload – High-Lift 32 tonnes 35 tonsRated Payload – Super High Lift 32 tonnes 35 tonsBucket Capacity Range 14-36 m 3 18.5-47 yd 3Cat Truck Match – Standard 785C, 789CCat Truck Match – High-Lift 789C, 793CCat Truck Match – Super High Lift 789C, 793CArticulation Angle 40ºEngine TorqueEngine Powerft-lb60005000400030002000100016001400120010008006004002001000 1100 1200 1300 1400 1500 1600Engine SpeedNetGross7000 9490hp1800 13421700N•m813467795423406727111355rpmBkw11931043894745596447298149Engine TorqueEngine PowerTransmissionTransmission TypeCat planetary power shiftForward 1 7.7 km/h 4.8 mphForward 2 13.4 km/h 8.3 mphForward 3 22.5 km/h 14 mphReverse 1 8.5 km/h 5.3 mphReverse 2 13.2 km/h 8.2 mphReverse 3 24.8 km/h 15.4 mphDirect Drive – Forward 1Lock-up disabledDirect Drive – Forward 2 13.7 km/h 8.5 mphDirect Drive – Forward 3 24 km/h 14.9 mphDirect Drive – Reverse 1 8.5 km/h 5.3 mphDirect Drive – Reverse 2 13.5 km/h 8.4 mphDirect Drive – Reverse 3 25.6 km/h 16 mph• Travel speeds based on two percent rolling resistance and53.5/85-57 tires in converter drive.Hydraulic System – Lift/TiltLift/Tilt System – CircuitOpenLift/Tilt System – Pump3x Piston, fixeddisplacementLift/Tilt – Pump1x Variable, PistonMax Flow at 1,710 rpm (3x) 1370 L/min 362 gal/minRelief Valve Setting – Lift/Tilt 32 800 kPa 4,750 psiCylinders – Lift/TiltDouble-actingLift Cylinder – Bore 318 mm 13 inLift Cylinder – Stroke 1660 mm 65.4 inTilt Cylinder – Bore 267 mm 10.5 inTilt Cylinder – Stroke 1140 mm 44.9 inNumber of Lift/Tilt Pumps 4Number of Lift Cylinders 2Number of Tilt Cylinders 2Hydraulic System – PilotPilot System – CircuitClosedPilot System – PumpGearMax Flow at 1,710 rpm 154 L/min 40.7 gal/minRelief Valve Setting – Pilot 2400 kPa 348 psiNumber of Pilot Pumps 11000 1100 1200 1300 1400 1500 1600Engine Speed1700rpm18 994F Wheel Loader specifications

Hydraulic Cycle TimeRackbackRaiseDumpLower Float Down (Empty)Power Down5.5 Seconds11.3 Seconds3.1 Seconds3.5 Seconds6.7 SecondsBrakesBrakes SAE J1473 OCT 90,ISO 3450:1992CabService Refill CapacitiesFuel Tank 3833 L 1,013 galCooling System 490 L 129 galCrankcase 286 L 75.5 galTransmission 350 L 92 galDifferentials and 621 L 164 galFinal Drives – FrontDifferentials and 621 L 164 galFinal Drives – RearDifferential/Final Drives (each) 621 L 164 galHydraulics – Lift/Tilt 390 L 103 galHydraulics – Brake Cooling 36 L 9 galHydraulics – Steering/Brake 208 L 55 galPump Drive – Front 7 L 2 galHydraulic System (including tank) 893 L 235.91 galDimensionsHinge Pin Height at Full Lift – Std 8157 mm 26 ft 10 in• Standard machine with 53.5/85-57 tires and 19 m 3 (24.5 yd 3 )5639 mm (222 in) spade edge rock bucket with teeth andsegments.• High-Lift machine with 53.5/85-57 tires and 18 m 3 (23.5 yd 3 )6223 mm (245 in) spade edge rock bucket with teeth andsegments.BucketsBucket Capacities 14 – 36 m 3 18.5 – 47 yd 3AxlesMaximum Single-Wheel Rise 677 mm 26.65 inand FallFrontFixedRearTrunnionOscillation Angle ±10°Air ConditioningStandard air conditioningsystem containsenvironmentally friendlyR134a refrigerantCab – ROPS/FOPSSAE J1394, SAE J11040APR88, ISO 3471-1:1986,ISO 3471:1994Caterpillar cab with separate Rollover Protective Structure/Falling Object Protective Structure (ROPS/FOPS) is standardin North America, Europe and Japan.• ROPS meets SAE J394, SAE J1040 APR 88, ISO 3471-01:1986and ISO 3471:1994 criteria.• FOPS meets SAE J231 JAN 81 and ISO 3449:1992 Level IIcriteria.Sound Performance ISO 6394:1998The operator sound exposure Leq (equivalent sound pressurelevel) measured according to the work cycle proceduresspecified in ANSI/SAE J1166 OCT98 is 75 dB(A), for the caboffered by Caterpillar, when properly installed, maintainedand tested with the doors and windows closed.• Hearing protection may be needed when operating with anopen operator station and cab (when not properly maintainedor doors/windows open) for extended periods or in noisyenvironment.• The exterior sound pressure level for the standard machinemeasured at a distance of 15 m (49.2 ft) according to the testprocedures specified in SAE J88 JUN86, mid-gear-movingoperation, is 87 dB(A).• The sound power level is 115 dB(A) measured accordingto the dynamic test procedure and conditions specifiedin ISO 6395:1988/Amd. 1:1996 for a standard machineconfiguration.VibrationEC 89/392 EECHydraulic System – SteeringSteering System – CircuitSteering System – PumpClosedPiston, variabledisplacementMax Flow @ 1,710 rpm (6900 kPa) 884 L/min 234 gal/min(2x)Relief Valve Setting – Steering 3100 kPa 4,500 psiNumber of Steering Pumps 2994F Wheel Loader specifications19

DimensionsAll dimensions are approximate.7109123845611 121314Standard* High Lift** Super High Lift***53.5/85-57 tires 53.5/85-57 tires 58/85-57 tires1 Height to Top of Exhaust Stacks 6988 mm (22.9 ft) 6988 mm (22.9 ft) 6747 mm (22.1 ft)2 Height to Top of ROPS/FOPS 6736 mm (22.1 ft) 6736 mm (22.1 ft) 6494 mm (21.3 ft)3 Height to Top of Hood 4833 mm (15.9 ft) 4833 mm (15.9 ft) 4591 mm (15.1 ft)4 Height to Center of Axle 1829 mm (6 ft) 1829 mm (6 ft) 1587 mm (5.2 ft)5 Bumper Clearance 1474 mm (4.8 ft) 1474 mm (4.8 ft) 1232 mm (4 ft)6 Ground Clearance 811 mm (2.7 ft) 811 mm (2.7 ft) 569 mm (1.9 ft)7 Reach at Maximum Lift/Dump 2309 mm (7.6 ft) 2764 mm (9.1 ft) 3400 mm (11.2 ft)8 Clearance at Maximum Lift/Dump 5578 mm (18.3 ft) 6024 mm (19.8 ft) 7296 mm (23.9 ft)9 Bucket Pivot at Maximum Lift 8140 mm (26.7 ft) 8479 mm (27.8 ft) 10 058 mm (33 ft)10 Overall Height – Bucket Raised 10 933 mm (35.9 ft) 10 643 mm (34.9 ft) 14 372 mm (47.2 ft)11 Length – Rear Axle to Bumper 4557 mm (15.0 ft) 4557 mm (15.0 ft) 4557 mm (15.0 ft)12 Wheel Base Length 6400 mm (21.0 ft) 6400 mm (21.0 ft) 6400 mm (21.0 ft)13 Length – Front Axle to Bucket Tip 5920 mm (19.4 ft) 6564 mm (21.5 ft) 8569 mm (28.1 ft)14 Overall Length 16 877 mm (55.4 ft) 17 521mm (57.5 ft) 19 526 mm (64.1 ft)*Standard machine equipped with 19 m 3 (24.5 yd 3 ) 222 in bucket.** High Lift machine equipped with 18 m 3 (23.5 yd 3 ) 245 in bucket.*** Super High Lift machine equipped with 36 m 3 (47 yd 3 ) 256 in bucket.20 994F Wheel Loader specifications

Bucket Capacity/Material Density Selection GuideRock Mining Applications only, for Coal Mining contact your Cat representative.The following table provides a guideline for bucket selection based on various material densities and estimated fill factors.Based on the new ratings, fill factors are expected to be 110-120% in cohesive materials with easy digging, 100-110% intypical shot rock loading, and 90-100% in poorly shot rock with large rocks and difficult penetration. For many miningapplications, the 994F standard lift is matched with the 19 m 3 (24.5 yd 3 ) rock bucket and the high lift is matched with the17 m 3 (22.5 yd 3 ) rock bucket.Bucket Capacity19yd 324.5Bucket Fill Factor115% 95%Standard115% 95%High-Lift1722.51519.5m 3 kg/m 31.4 1.6 1.8 2.0 2.2 2.4 2.62.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4Material Density(Thousands)lb/yd 3Changes in bucket weight, including field installedwear iron, can impact rated payload. Consult yourCaterpillar dealer for assistance in selecting andconfiguring the proper bucket for the application.The Caterpillar Large Wheel Loader Payload Policyis a guideline intended to maximize wheel loaderstructural and component life.994F Wheel Loader specifications21

Operating Specifications – Standard LiftFor machines equipped with 53.5/85-57, 76 PR L-5 tires – see additional tables for other tire sizesCoal BucketNarrow Bucket Wide Bucket (6200 mm/(5640 mm/222 in) (6200 mm/244 in) 244 in)StraightEdgeCoalSpade Edge Spade Edge BucketRock Bucket Rock Bucket Teeth &Teeth & Segment Teeth & Segment SegmentRated capacity (§) m 3 14 15 17 19 18 19 31yd 3 18.5 19.5 22.5 25 23.5 25 41Width (§) mm 5640 5640 5640 5640 6200 6200 6200ft/in 18' 6" 18' 6" 18' 6" 18' 6" 20' 4" 20' 4" 20' 4"Struck capacity (§) m 3 11 12 14 15 14.5 15 27yd 3 14.4 15.7 18.3 19.6 19.0 19.6 35.3Dump clearance at full lift mm 5771 5771 5663 5556 5663 5563 5635and 45° discharge (§) ft/in 18' 11" 18' 11" 18' 7" 18' 3" 18' 7" 18' 3" 18' 6"Reach at full lift mm 2071 2071 2160 2266 2160 2278 2306and 45° discharge (§) ft/in 6' 9" 6' 9" 7' 1" 7' 5" 7' 1" 7' 6" 7' 6"Reach with lift arms mm 4916 4916 5056 5206 5056 5210 5179horizontal and bucket level ft/in 16' 1" 16' 1" 16' 7" 17' 0" 16' 7" 17' 1" 17' 0"Digging depth (§) mm 108 108 108 108 108 108 63in 4" 4" 4" 4" 4" 4" 2"Overall length (§) mm 16 604 16 604 16 744 16 894 16 744 16 898 16 830ft/in 54' 6" 54' 6" 54' 11" 55' 5" 54' 11" 55' 5" 55' 2"Overall height with bucket mm 10 719 10 719 10 866 10 911 10 636 10 621 10 960at full raise (§) ft/in 35' 2" 35' 2" 35' 7" 35' 9" 34' 11" 34' 10" 39' 11"Loader clearance circle with mm 12 668 12 668 12 704 12 742 12 965 13 002 13 073bucket in carry position (§) ft/in 41' 7" 41' 7" 41' 8" 41' 9" 42' 6" 42' 7" 42' 11"Static tipping load straight** (§) kg 130 783 131 140 130 266 128 499 127 909 126 522 129 295lb 288,327 289,114 287,187 283,292 281,991 278,933 285,046Static tipping load kg 113 391 113 684 112 784 111 091 110 539 109 241 111 719at full 40° turn** (§) lb 250,188 250,835 248,849 245,113 243,895 241,032 246,298Breakout force*** (§) kN 1134 1133 1055 989 1060 995 974lb 254,993 254,709 237,173 222,336 238,289 223,685 218,964Operating weight** (§) kg 191 899 192 039 192 699 193 779 193 999 194 729 195 169lb 423,064 423,373 424,828 427,209 427,694 429,303 430,273(§) Specifications rating conform to all applicable standards recommended by the Society of Automotive Engineers. SAE standard J732c governs loader ratingsand is denoted in the chart by (§).* Dimensions are measured to the tip of the bucket teeth to provide accurate clearance data. SAE standard specifies the cutting edge.** Static tipping load and operating weight shown are based on standard machine configuration with 53.5/85-57 tires, full fuel tank, coolant and lubricants.*** Measured 102 mm (4 in) behind tip of cutting edge with the bucket hinge pin as pivot point in accordance with SAE J732c.22 994F Wheel Loader specifications

Changes in Standard Lift Specifications due to Tire SizeDimensional changes50/80-57 52/80-57 55/80R57 53.5/85-57 58/85-57Dump clearance at full lift mm –136 –143 –89 0 +17and 45° discharge in –5 –6 –4 0 +0.7Reach at full lift and mm +118 +143 +68 0 –1545° discharge in +5 +6 +3 0 –0.6Reach with lift arms mm +118 +143 +68 0 –15horizontal and bucket level in +5 +6 +3 0 –0.6Digging depth mm +136 +143 +89 0 –17in +5 +6 +4 0 –0.7Overall length mm +105 +111 +70 0 –12in +4 +4 +3 0 –0.5Overall height with bucket mm –136 –143 –89 0 +17at full raise in –5 –6 –4 0 +0.67Total width over tires mm 5305 5302 5509 5460 5524in 209 209 217 214 217Weight changes50/80-57 52/80-57 55/80R57 53.5/85-57 58/85-57Static tipping load straight kg –4234 –3339 +50 0 +327lb –9,334 –7,361 +110 0 +721Static tipping load kg –3738 –2953 +44 0 +285at full 40° turn lb –8,241 –6,510 +97 0 +628Operating weight kg –5388 –4256 +64 0 +416lb –11,878 –9,383 +141 0 +917994F Wheel Loader specifications23

Operating Specifications – High LiftFor machines equipped with 53.5/85-57, 76 PR L-5 tires – see additional tables for other tire sizesCoal BucketNarrow Bucket Wide Bucket (6200 mm/(5640 mm/222 in) (6200 mm/244 in) 244 in)StraightEdgeCoalSpade Edge Spade Edge BucketRock Bucket Rock Bucket Teeth &Teeth & Segment Teeth & Segment SegmentRated capacity (§) m 3 14 15 17 19 18 19 31yd 3 18.5 19.5 22.5 25 23.5 25 41Width (§) mm 5640 5640 5640 5640 6200 6200 6200ft/in 18' 6" 18' 6" 18' 6" 18' 6" 20' 4" 20' 4" 20' 4"Struck capacity (§) m 3 11 12 14 15 14.5 15 27yd 3 14.4 15.7 18.3 19.6 19 19.6 35.3Dump clearance at full lift mm 6110 6110 6002 5895 6002 5902 5974and 45° discharge (§) ft/in 20' 0" 20' 0" 19' 8" 19' 4" 19' 8" 19' 4" 19' 7"Reach at full lift mm 2632 2632 2721 2827 2721 2839 2867and 45° discharge (§) ft/in 8' 8" 8' 8" 8' 11" 9' 3" 8' 11" 9' 4" 9' 5"Reach with lift arms mm 5556 5556 5696 5846 5696 5850 5819horizontal and bucket level ft/in 18' 2" 18' 2" 18' 8" 19' 4" 18' 8" 19' 2" 19' 1"Digging depth (§) mm 123 123 123 123 123 123 78in 5" 5" 5" 5" 5" 5" 3"Overall length (§) mm 17 396 17 396 17 536 17 686 17 536 17 690 17 622ft/in 57' 0" 57' 0" 57' 6" 58' 0" 57' 6" 58' 0" 57' 10"Overall height with mm 11 058 11 058 11 205 11 250 10 960 10 975 12 184bucket at full raise (§) ft/in 36' 3" 36' 3" 36' 9" 36' 11" 36' 0" 36' 0" 40' 0"Loader clearance circle with mm 12 959 12 959 12 993 13 030 13 249 13 285 13 285bucket in carry position (§) ft/in 42' 6" 42' 6" 42' 7" 42' 10" 43' 6" 43' 7" 43' 7"Static tipping load straight** (§) kg 108 695 108 926 108 111 106 543 105 978 104 795 107 068lb 239,631 240,140 238,344 234,887 233,641 231,033 236,044Static tipping load kg 93 575 93 757 92 914 91 399 90 871 89 753 91 770at full 40° turn** (§) lb 206,297 206,699 204,840 201,500 200,336 197,871 202,318Breakout force*** (§) kN 1091 1091 1015 951 1020 957 936lb 245,475 245,475 228,375 213,793 229,305 215,325 210,421Operating weight** (§) kg 194 634 194 774 195 434 196 514 196 734 197 464 197 904lb 429,094 429,403 430,858 433,239 433,724 435,333 436,303(§) Specifications rating conform to all applicable standards recommended by the Society of Automotive Engineers. SAE standard J732c governs loader ratingsand is denoted in the chart by (§).* Dimensions are measured to the tip of the bucket teeth to provide accurate clearance data. SAE standard specifies the cutting edge.** Static tipping load and operating weight shown are based on standard machine configuration with 53.5/85-57 tires, full fuel tank, coolant and lubricants.*** Measured 102 mm (4 in) behind tip of cutting edge with the bucket hinge pin as pivot point in accordance with SAE J732c.24 994F Wheel Loader specifications

Changes in High Lift Specifications due to Tire SizeDimensional changes50/80-57 52/80-57 55/80R57 53.5/85-57 58/85-57Dump clearance at full lift mm –136 –143 –89 0 +17and 45° discharge in –5 –6 –3.5 0 +0.7Reach at full lift and mm +118 +143 +68 0 –1545° discharge in +5 +6 +3 0 –0.6Reach with lift arms mm +118 +143 +68 0 –15horizontal and bucket level in +5 +6 +3 0 –0.6Digging depth mm +136 +143 +89 0 –17in +5 +6 +4 0 –0.7Overall length mm +90 +94 +59 0 –12in +4 +4 +2 0 –0.5Overall height with bucket mm –136 –143 –89 0 +17at full raise in –5 –6 –4 0 +0.7Total width over tires mm 5305 5302 5509 5460 5524in 209 209 217 214 217Weight changes50/80-57 52/80-57 55/80R57 53.5/85-57 58/85-57Static tipping load straight kg –3643 –2878 +43 0 +281lb –8,031 –6,344 +95 0 +620Static tipping load kg –3217 –2541 +38 0 +248at full 40° turn lb –7,092 –5,602 +84 0 +548Operating weight kg –5388 –4256 +64 0 +416lb –11,878 –9,383 +141 0 +917994F Wheel Loader specifications25

Operating Specifications – Super High LiftMachines only equipped with 58/85-57 tires & Coal BucketCoal Bucket(6500 mm/256 in)Serrated EdgeCoal BucketRated capacity (§) m 3 36yd 3 47Struck capacity (§) m 3 30yd 3 39.2Dump clearance at full lift mm 7336and 45° discharge (§) ft/in 24' 0"Reach at full lift mm 3386and 45° discharge (§) ft/in 11' 1"Reach with lift arms mm 7543horizontal and bucket level ft/in 24' 9"Digging depth (§) mm 299ft/in 1' 0"Overall length (§) mm 19 504ft/in 63' 1"Overall height with bucket mm 14 412at full raise (§) ft/in 47' 3"Loader clearance circle with mm 14 262bucket in carry position (§) ft/in 46' 10"Static tipping load straight** (§) kg 83 444lb 183,962Static tipping load kg 69 748at full 40° turn** (§) lb 153,768Breakout force*** (§) kN 693lb 155,925Operating weight** (§) kg 211 970lb 467,313Width over tires mm 552458/85-57 in 217(§) Specifications rating conform to all applicable standards recommended by the Society of Automotive Engineers. SAE standard J732c governs loader ratingsand is denoted in the chart by (§).* Dimensions are measured to the tip of the bucket teeth to provide accurate clearance data. SAE standard specifies the cutting edge.** Static tipping load and operating weight shown are based on standard machine configuration with 53.5/85-57 tires, full fuel tank, coolant and lubricants.*** Measured 102 mm (4 in) behind tip of cutting edge with the bucket hinge pin as pivot point in accordance with SAE J732c.26 994F Wheel Loader specifications

Standard EquipmentStandard equipment may vary. Consult your Caterpillar dealer for details.ELECTRICALAlarm, back-upAlternator, dual 80 ampBatteries, dryConverter, 10/15 amp, 24V to 12VLighting system, (halogen, working lights, access andservice platform lighting)Starting and charging system, 24VStarter lockout in bumperTransmission lockout in bumperOPERATOR ENVIRONMENTAir conditionerCab, sound suppressed and pressurized, separate externalrollover protective structure (ROPS/FOPS) Radio readyfor (entertainment) includes antenna, speakers andconverter (12-volt 5-amp) and power portCab, cleanout hoseCigar lighter, ashtrayCoat hookControls, lift and tilt functionHeater, defrosterHorn, airInstrumentation, gaugesCoolant temperatureEngine hour meterHydraulic oil temperaturePower Train oil temperatureLight, cab, domeLunchbox, beverage holdersMirrors, rearview (externally mounted)Rimpull Control SystemSeat, Cat Comfort (cloth), air suspension, six-way adjustableSeat belt, retractable, 76 mm (3 in) wideSTIC Control SystemTinted glassTrainer seat with lap beltTransmission gear indicatorVital Information Management System (VIMS)External data port, Integral Payload Control SystemMessage center, universal gaugeVIMS KeypadWet-Arm Wipers/Washers (front and rear)Intermittent front and rear wipersPOWER TRAINBrakes, oil-cooled, multi-disc, service/secondaryDriveline parking brakeEngine, 3516B HD EUI (SCAC) Diesel,turbocharged/aftercooledFuel priming pump (electric)Ground level engine shutoffPrecleaner, engine air intake (above hood)Radiator, Next Generation Modular (NGMR)Power train oil coolers (2) air to oil, (2) water to oilStarting aid, ether, automaticThrottle lock, electronicTorque converter, Impeller Clutch (ICTC)with LUC, Rimpull Control SystemTransmission, planetary powershift, 3F/3R electronic controlOTHERAir tank, ECC compliant (EN286)Air line dryerAutomatic bucket lift kickout/positionerAutomatic lubrication systemBase machine price includes a rim allowanceBlower fanCouplings, Caterpillar O-ring face sealsDoors, service access (locking)Ecology drains for engine, radiator, hydraulic tank, steeringand brake tank, and brake cooling tankEngine oil change system, high speed, WigginsFast fill fuel system (Shaw-Aero)Fuel tank, 4641 L (1,226 gal)Hitch, drawbar with pinHoses, Caterpillar XTHydraulic, steering and brake filtration/screening systemImproved Service CenterMufflers (4)Oil sampling valvesPremixed 50% concentration of extended life coolant withfreeze protection to –34° C (–29° F)Rear access to cab and service platformSteering, load sensingSupplemental steering systemVandalism protection caplocks994F Wheel Loader specifications27

Optional EquipmentWith approximate changes in operating weights.Optional equipment may vary. Consult your Caterpillar dealer for specifics.kglbBUCKETSSpade EdgeNARROW – 5650 mm (222 in)Rock – 14 m 3 (18.5 yd 3 ) (J800) 18 338 40,429Rock – 15 m 3 (19.5 yd 3 ) (J800) 18 481 40,744Rock – 17 m 3 (22.5 yd 3 ) (J800) 18 217 40,162Rock – 19 m 3 (25 yd 3 ) (J800) 20 197 44,526WIDE – 6220 mm (245 in)Rock – 18 m 3 (23.5 yd 3 ) (J800) 20 167 44,460Rock – 19 m 3 (25 yd 3 ) (J800) 20 444 45,072Straight EdgeCoal – 32 m 3 (42 yd 3 ) (J700) 20 167 44,460Serrated EdgeCoal – 36 m 3 (47 yd 3 ) (none) 20 444 45,072GROUND ENGAGING TOOLSBUCKET TIPS*Heavy duty – long – rock (J800) 88 193Heavy duty – abrasion – rock (J800) 105 232Heavy duty – penetration – rock (J800) 97 214Penetration – rock (J800) 54 120Heavy duty – long – coal (J700) 51 113Heavy duty – abrasion – coal (J700) 66 145BUCKET WINGSLow profile 350 772kglbPOWER TRAINCrankcase guard 300 662Engine prelube 1 3Engine oil renewal system 66 145Sy-Klone turbine precleaner 11 25RIMS914 mm (36") wide 1813 3,9961118 mm (44") widewith 126 mm (6") flange 1925 4,2451194 mm (47") widewith 126 mm (6") flange 1930 4,255ELECTRICALCAES, attachment ready 23 50VIMS, wireless II 0 0Camera, rear vision 2 4OTHERCab precleaner 2 5Product Link** 1 3** Requires multiple quantities.** Available mid-2005.Mandatory Attachments (select one from each group)Mandatory and optional equipment may vary. Consult your Caterpillar dealer for specifics.kglbLIFT ARRANGEMENTSStandard 0 0High Lift 3186 7,024Super High Lift 17 729 39,085FUEL LINESNo heater 0 0With heater 6 13Cold weather starting 32 71kglbRIMS914 mm (36") wide 0 01118 mm (44") widewith 126 mm (6") flange 428 9441194 mm (47") widewith 126 mm (6") flange 459 1,012STARTERSAir start, turbine, Ingersoll 0 0Air start, turbine, TDI 0 0Electric- not recommended in ambienttemperatures below 0° C (32° F) 0 028 994F Wheel Loader specifications

Notes994F Wheel Loader specifications 29

Notes30994F Wheel Loader specifications

Notes994F Wheel Loader specifications 31

994F Wheel LoaderFor more complete information on Cat products, dealer services,and industry solutions, visit us on the web at www.cat.com© 2006 CaterpillarAll Rights ReservedPrinted in U.S.A.Materials and specifications are subject to change without notice.Featured machines in photos may include additional equipment.See your Caterpillar dealer for available options.AEHQ5640-01 (9-06)CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and thePOWER EDGE trade dress, as well as corporate and product identity used herein,are trademarks of Caterpillar and may not be used without permission.R