WSM User Guide - WatchGuard Technologies
WSM User Guide - WatchGuard Technologies WSM User Guide - WatchGuard Technologies
Working with Devices on a Management Server6 From the Device Type drop-down list, select the Firebox model.7 For devices that do not use a dynamic IP address, type the IP address or host name. For devices thatuse a dynamic IP address, type the Dynamic DNS service client name.8 Type the status passphrase. This is the status passphrase for the Firebox X Edge or SOHO 6 that youconfigured when you set up VPN Manager access or WatchGuard Management access.9 Type the configuration passphrase. This is the configuration passphrase for the Firebox X Edge orSOHO 6 that you configured when you set up VPN Manager access or WatchGuard Managementaccess.10 If the Firebox X Edge or SOHO 6 uses a dynamic IP address, type the Dynamic DNS client sharedsecret.11 Click Next.The Configure WINS and DNS screen appears.12 Type primary and secondary addresses for the WINS and DNS servers this device uses, if any.13 Type the domain name for this device, if any. Click Next.The Provide Contact Information screen appears.258 WatchGuard System Manager
Scheduling Firebox X Edge Firmware Updates14 You can select an existing contact record for this device, or click Add to add a new contact record forthis device. To delete an existing contact record, select it and click Delete.15 Click Next. The Configure the Device screen appears. Click Next on this screen to configure thedevice with the new management settings and add it to the Management Server. If the device isalready managed by another server, or configured for management by this server, a warning dialogbox appears. Click Yes to continue.You cannot configure Firebox SOHO devices with the Management Server.16 Click Close to close the Add New Device wizard.Scheduling Firebox X Edge Firmware UpdatesFirebox® X Edge devices must have a firmware update to operate with the advanced features of theManagement Server. In the future, more firmware updates could be required. These firmware updatesare installed on the Management Server, and the Management Server loads them on the Edge devices.WatchGuard® System Manager can install firmware updates to a group of Edge devices easily. You canupdate firmware on groups of devices with one operation, either immediately or on a schedule.You get firmware updates from LiveSecurity.1 In the Device Management tab in WatchGuard System Manager, select the Management Server.The Management Server settings page appears.User Guide 259
- Page 226 and 227: Managing Devices with the Managemen
- Page 228 and 229: Managing Devices with the Managemen
- Page 230 and 231: Managing Devices with the Managemen
- Page 232 and 233: Adding Devices to the Management Se
- Page 234 and 235: Using the Device Management Page17
- Page 236 and 237: Using the Device Management PageCon
- Page 238 and 239: Monitoring VPNsAdding a Firebox VPN
- Page 240 and 241: PKI in a WatchGuard VPNPKI in a Wat
- Page 242 and 243: Managing the Certificate Authority2
- Page 244 and 245: Tunneling ProtocolsVirtual private
- Page 246 and 247: IP Addressingsecurity of the networ
- Page 248 and 249: Network TopologyThis topology is th
- Page 250 and 251: WatchGuard VPN SolutionsSplit tunne
- Page 252 and 253: VPN Scenarios• You make tunnels b
- Page 254 and 255: VPN ScenariosSmall Company Using Ex
- Page 256 and 257: Adding VPN Resourcesapplies a VPN r
- Page 258 and 259: Making Tunnels Between Devices3 To
- Page 260 and 261: Removing Tunnels and Devices2 Expan
- Page 262 and 263: Configuring a GatewayTo configure t
- Page 264 and 265: Making a Manual Tunnel18 When you c
- Page 266 and 267: Making a Manual Tunnel7 From the Ty
- Page 268 and 269: Making a Tunnel Policy2 Make the ch
- Page 270 and 271: Setting up Outgoing Dynamic NAT thr
- Page 272 and 273: Working with Devices on a Managemen
- Page 274 and 275: Working with Devices on a Managemen
- Page 278 and 279: Scheduling Firebox X Edge Firmware
- Page 280 and 281: Using the Firebox X Edge Management
- Page 282 and 283: Using the Firebox X Edge Management
- Page 284 and 285: Using the Firebox SOHO 6 Management
- Page 286 and 287: Creating and Applying Edge Configur
- Page 288 and 289: Creating and Applying Edge Configur
- Page 290 and 291: Creating and Applying Edge Configur
- Page 292 and 293: Managing Firebox X Edge Network Set
- Page 294 and 295: Using AliasesNaming aliases on the
- Page 296 and 297: Using Aliases3 Click Aliases.The al
- Page 298 and 299: Configuring WINS and DNS Servers•
- Page 300 and 301: Adding New Users to the PPTP_Users
- Page 302 and 303: Preparing the Client Computers- To:
- Page 304 and 305: Creating and Connecting a PPTP RUVP
- Page 306 and 307: Creating and Connecting a PPTP RUVP
- Page 308 and 309: Getting Started with WebBlocker4 In
- Page 310 and 311: Activating WebBlocker4 Click Next.5
- Page 312 and 313: Configuring WebBlocker2 Select the
- Page 314 and 315: Configuring WebBlocker3 Click the A
- Page 316 and 317: Scheduling a WebBlocker Action298 W
- Page 318 and 319: Installing the Software Licensespam
- Page 320 and 321: Activating spamBlocker3 From Policy
- Page 322 and 323: Creating Rules for Bulk and Suspect
- Page 324 and 325: Customizing spamBlocker Using Multi
Working with Devices on a Management Server6 From the Device Type drop-down list, select the Firebox model.7 For devices that do not use a dynamic IP address, type the IP address or host name. For devices thatuse a dynamic IP address, type the Dynamic DNS service client name.8 Type the status passphrase. This is the status passphrase for the Firebox X Edge or SOHO 6 that youconfigured when you set up VPN Manager access or <strong>WatchGuard</strong> Management access.9 Type the configuration passphrase. This is the configuration passphrase for the Firebox X Edge orSOHO 6 that you configured when you set up VPN Manager access or <strong>WatchGuard</strong> Managementaccess.10 If the Firebox X Edge or SOHO 6 uses a dynamic IP address, type the Dynamic DNS client sharedsecret.11 Click Next.The Configure WINS and DNS screen appears.12 Type primary and secondary addresses for the WINS and DNS servers this device uses, if any.13 Type the domain name for this device, if any. Click Next.The Provide Contact Information screen appears.258 <strong>WatchGuard</strong> System Manager