WSM User Guide - WatchGuard Technologies
WSM User Guide - WatchGuard Technologies WSM User Guide - WatchGuard Technologies
Setting Up the Log ServerSetting Up the Log ServerThe Log Server collects logs from each WatchGuard® Firebox® managed by WSM.1 On the computer that has the Log Server software installed, select the Log Server icon from theWatchGuard toolbar.If the WatchGuard toolbar does not appear, right-click in the system tray and select Toolbars > WatchGuard.,The WatchGuard Log Server Configuration dialog box appears.2 Type the encryption key to use for the secure connection between the Firebox and the Log Servers.Log Server encryption keys are a minimum of eight characters.3 Confirm the encryption key.4 Select a directory to keep all logs, reports, and report definition files. We recommend that you usedefault location.5 Click OK.6 Click Start > Control Panel. Go to Power Options. Select the Hibernate tab and disablehibernation. This is to prevent the Log Server from shutting down when the computer hibernates.7 Make sure the Log Server and the Firebox are set to the same system time. For information onsetting system time, see the “Basic Firebox Administration” chapter.Changing the Log Server encryption keyTo change the encryption key on the Log Server:1 Right-click the Log Server icon on the WatchGuard toolbar and select Status/Configuration.2 Select File > Set Log Encryption Key.82 WatchGuard System Manager
Setting up the Firebox for a Designated Log Server3 Type the new log encryption key two times.4 In Policy Manager, select Logging and type the new log encryption key.5 Click OK.6 Do the same procedure on the Firebox.Setting up the Firebox for a Designated Log ServerIt is recommended that you have a minimum of one Log Server to use WatchGuard System Manager.You can select a different primary Log Server and one or more backup Log Servers.1 From Policy Manager, select Setup > Logging.The Logging Setup dialog box appears.2 Select the Log Server or servers you want to use. Click the Send log messages to the Log Serversat these IP addresses check box.Adding a Log Server for a Firebox1 From Policy Manager, select Setup > Logging.The Logging Setup dialog box appears.User Guide 83
- Page 50 and 51: Firebox System Manager Menus and To
- Page 52 and 53: Seeing Basic Firebox and Network St
- Page 54 and 55: Seeing Basic Firebox and Network St
- Page 56 and 57: Monitoring Firebox TrafficMonitorin
- Page 58 and 59: Clearing the ARP CacheLearning more
- Page 60 and 61: Using the Performance Console2 From
- Page 62 and 63: Using the Performance ConsoleWorkin
- Page 64 and 65: Viewing Number of Connections by Po
- Page 66 and 67: Viewing Information About Firebox S
- Page 68 and 69: Viewing Information About Firebox S
- Page 70 and 71: Viewing Information About Firebox S
- Page 72 and 73: Using HostWatchWhile the top part o
- Page 74 and 75: Using HostWatchPausing the HostWatc
- Page 76 and 77: Working with Licenses3 Below Option
- Page 78 and 79: Working with Licenses2 Expand Licen
- Page 80 and 81: Setting a Friendly Name and Time Zo
- Page 82 and 83: Changing the Firebox Passphrases10
- Page 84 and 85: Recovering a FireboxTo manually res
- Page 86 and 87: Recovering a Firebox68 WatchGuard S
- Page 88 and 89: Opening a Configuration Fileto a se
- Page 90 and 91: About Firebox Backup ImagesSaving a
- Page 92 and 93: Working with AliasesAlias names are
- Page 94 and 95: Using Global SettingsEnable TOS for
- Page 96 and 97: Managing a Firebox from a Remote Lo
- Page 98 and 99: Managing a Firebox from a Remote Lo
- Page 102 and 103: Setting up the Firebox for a Design
- Page 104 and 105: Setting Global Logging and Notifica
- Page 106 and 107: Setting Global Logging and Notifica
- Page 108 and 109: Types of Log MessagesTypes of Log M
- Page 110 and 111: LogViewer SettingsLogViewer Setting
- Page 112 and 113: Using LogViewerSearching in LogView
- Page 114 and 115: Using LogViewerTo convert a log fil
- Page 116 and 117: Changing Firebox Interface IP Addre
- Page 118 and 119: Changing Firebox Interface IP Addre
- Page 120 and 121: About Multiple WAN Support3 Under H
- Page 122 and 123: About Multiple WAN SupportConfiguri
- Page 124 and 125: Adding Secondary NetworksIf your Fi
- Page 126 and 127: Configuring Dynamic DNSMake sure th
- Page 128 and 129: Configuring RoutesFor more informat
- Page 130 and 131: Configuring Related Hostsfor that I
- Page 132 and 133: Using Dynamic NATUsing Dynamic NATD
- Page 134 and 135: Using 1-to-1 NAT4 Click OK. Save th
- Page 136 and 137: Using 1-to-1 NATa VPN tunnel is con
- Page 138 and 139: Configuring Static NAT for a Policy
- Page 140 and 141: How User Authentication Worksvent a
- Page 142 and 143: Configuring the Firebox as an Authe
- Page 144 and 145: Configuring the Firebox as an Authe
- Page 146 and 147: Configuring SecurID Authentication6
- Page 148 and 149: Configuring LDAP Authentication3 In
Setting Up the Log ServerSetting Up the Log ServerThe Log Server collects logs from each <strong>WatchGuard</strong>® Firebox® managed by <strong>WSM</strong>.1 On the computer that has the Log Server software installed, select the Log Server icon from the<strong>WatchGuard</strong> toolbar.If the <strong>WatchGuard</strong> toolbar does not appear, right-click in the system tray and select Toolbars > <strong>WatchGuard</strong>.,The <strong>WatchGuard</strong> Log Server Configuration dialog box appears.2 Type the encryption key to use for the secure connection between the Firebox and the Log Servers.Log Server encryption keys are a minimum of eight characters.3 Confirm the encryption key.4 Select a directory to keep all logs, reports, and report definition files. We recommend that you usedefault location.5 Click OK.6 Click Start > Control Panel. Go to Power Options. Select the Hibernate tab and disablehibernation. This is to prevent the Log Server from shutting down when the computer hibernates.7 Make sure the Log Server and the Firebox are set to the same system time. For information onsetting system time, see the “Basic Firebox Administration” chapter.Changing the Log Server encryption keyTo change the encryption key on the Log Server:1 Right-click the Log Server icon on the <strong>WatchGuard</strong> toolbar and select Status/Configuration.2 Select File > Set Log Encryption Key.82 <strong>WatchGuard</strong> System Manager