ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Creating debug hardware target configurationsFigure 5-14 Platform configuration and identificationAfter the platform configuration is complete, the control pane shows the revised scan chaindevice/platform configuration in use and the name of the loaded platform. The tree diagram alsoreflects the new configuration.NoteYou cannot add, move, or remove any devices when a platform configuration is in use.During the configuration process, the label on the Select Platform... button changes to read asClear Platform.5.24.1 See alsoTasks• Manually selecting a platform on page 5-43• Clearing a platform assignment from a debug hardware configuration on page 5-44• Adding new platforms on page 5-45.Concepts• About platform detection and selection on page 5-40.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 5-42ID021112Non-Confidential
Creating debug hardware target configurations5.25 Manually selecting a platformFor platforms that cannot be detected automatically, you can perform a manual selection froma list of supported platforms. To do this, click the Select Platform... button from the DebugSystem pane of the Debug Hardware Config utility, and the Select Platform dialog box displays.The following figure shows an example:Figure 5-15 List of supported platformsIn the Select Platform dialog box, select your platform and click OK. This causes the entireplatform configuration to be loaded, in a similar manner as when you are autodetecting aplatform.During the configuration process, the label on the Select Platform... button changes to read asClear Platform.You can also create your own platform files and add them to the list of available platforms.5.25.1 See alsoTasks• Autodetecting a platform on page 5-41• Clearing a platform assignment from a debug hardware configuration on page 5-44• Adding new platforms on page 5-45• Adding autoconfigure support for new platforms on page 5-46.Concepts• About platform detection and selection on page 5-40.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 5-43ID021112Non-Confidential
Page 1 and 2:
®ARMDS-5Version 5.9Using the Debug
Page 3 and 4:
Conformance NoticesThis section con
Page 5 and 6:
Contents4.6 Restarting the debug ha
Page 7 and 8:
Contents10.6 Auto Configure button
Page 9 and 10:
Conventions and feedback• the ser
Page 11 and 12:
Getting started with the debug hard
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 3Configuring network settin
Page 21 and 22:
Configuring network settings for yo
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34: Managing the firmware on your debug
Page 43 and 44: Chapter 5Creating debug hardware ta
Page 45 and 46: Creating debug hardware target conf
Page 83: Creating debug hardware target conf
Page 97 and 98: Configuring CoreSight systems6.1 Ab
Page 99 and 100: Configuring CoreSight systems6.3 Co
Page 101 and 102: Configuring CoreSight systems6.5 Ab
Page 103 and 104: Configuring CoreSight systems6.7 Fo
Page 105 and 106: Configuring CoreSight systems2. Loc
Page 107 and 108: Configuring CoreSight systems• To
Page 109 and 110: Configuring CoreSight systems6.10.1
Page 111 and 112: Configuring CoreSight systemsName=T
Page 113 and 114: Configuring CoreSight systemsName=T
Page 115 and 116: Configuring CoreSight systems6.13.1
Page 117 and 118: Configuring CoreSight systems6.15 C
Page 123 and 124: Chapter 7Using TraceThe following t
Page 125 and 126: Using Trace7.2 Trace hardware captu
Page 127 and 128: Using TraceConcepts• About using
Page 129 and 130: Chapter 8Debugging with your debug
Page 131 and 132: Debugging with your debug hardware
Page 133 and 134: Debugging with your debug hardware
Page 135 and 136:
Debugging with your debug hardware
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Chapter 9Configuring debug hardware
Page 153 and 154:
Configuring debug hardware for GDB9
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?