ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Managing the firmware on your debug hardware unitFigure 4-5 Confirming that you want to install the component fileWhen attempting to install a firmware update file, if you are using an older version of RVIUpdate, for example a pre-RVI v1.5 release, an error message appears as shown in thefollowing figure:Figure 4-6 Warning messageNoteBefore proceeding with your firmware update, you must upgrade your RVI Update utilityto the latest software.Similarly, if you are using a version of hardware that is incompatible with the firmwareyou are attempting to install, an error message similar to the one shown in the followingfigure:Figure 4-7 Error when using an incompatible version of hardware7. In the Install update dialog box, click:• Continue to confirm that you want to install the components• Cancel to make no change to the debug hardware unit.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 4-7ID021112Non-Confidential
Managing the firmware on your debug hardware unitWhen you click Continue, the RVI Update utility uploads the component file to the debughardware unit. The debug hardware unit unpacks the component file, and installs theupdate or patch that it contains. The progress of the installation is displayed as shown inthe following figure:Figure 4-8 Progress during an installationThe debug hardware unit might automatically reboot itself as part of this procedure,depending on the patch or update that you are installing. The progress of the reboot isdisplayed as shown in the following figure:Figure 4-9 Progress when rebooting during an installationDuring the installation, the FLASH LED lights up, showing that the unit is accessing itsinternal flash storage. During this time, do not disconnect power from the debug hardwareunit. If a problem occurs during the installation, you must troubleshoot the firmwareupgrade installation.NoteDuring the installation, the Abort button is enabled. This means that you can safely stopthe installation from proceeding by clicking this button. If the Abort button is not enabled,for example during rebooting, you cannot stop the reboot.When the installation is complete, a message is displayed as shown in the followingfigure:Figure 4-10 Message showing a successful installation4.4.1 See alsoTasks• Starting the debug hardware configuration utilities on page 2-3• Viewing software version numbers on page 4-4• Upgrading an LVDS probe on page 4-10.Concepts• About templates and firmware files on page 4-2ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 4-8ID021112Non-Confidential
Page 1 and 2: ®ARMDS-5Version 5.9Using the Debug
Page 3 and 4: Conformance NoticesThis section con
Page 5 and 6: Contents4.6 Restarting the debug ha
Page 7 and 8: Contents10.6 Auto Configure button
Page 9 and 10: Conventions and feedback• the ser
Page 11 and 12: Getting started with the debug hard
Page 19 and 20: Chapter 3Configuring network settin
Page 21 and 22: Configuring network settings for yo
Page 33 and 34: Managing the firmware on your debug
Page 37: Managing the firmware on your debug
Page 43 and 44: Chapter 5Creating debug hardware ta
Page 45 and 46: Creating debug hardware target conf
Page 89 and 90:
Creating debug hardware target conf
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128:
Using TraceConcepts• About using
Page 129 and 130:
Chapter 8Debugging with your debug
Page 131 and 132:
Debugging with your debug hardware
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Chapter 9Configuring debug hardware
Page 153 and 154:
Configuring debug hardware for GDB9
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?