ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Managing the firmware on your debug hardware unit4.4 Installing a firmware update or patch releaseYou perform the same basic procedure for updating your firmware to a new version or applyinga patch to the current version. However, if you are updating from a previous version of thefirmware, for example from 4.4 to 4.5, you must upgrade to the base version first, then applyany patch related to that version. For example, if you have a DSTREAM unit:1. Update your DSTREAM unit with ARM-RVI-4.5.0-9-base.dstream.2. If a patch file is provided, such as ARM-RVI-4.5.0-12-patch.dstream, apply the patch toyour DSTREAM unit.If you want to restore the firmware to its original state after installing an upgrade, you canreinstall the original firmware file. This file is obtainable from the ARM website.NoteIf you have been running the Log Client utility, then make sure you stop it before performing anupdate. Although the Log Client utility does not prevent the update fromcompleting, it can takelonger to complete.To install an update or patch to the firmware on a debug hardware unit:1. To open the RVI Update utility, select:Start → All Programs → ARM DS-5 → Debug Hardware → Debug HardwareUpdateThe RVI Update utility is displayed. An example is shown in the following figure:Figure 4-2 RVI Update utility2. Either:• select the debug hardware unit from the list• enter the IP address or host name of the debug hardware unit in the Other TCP/IPDevices field.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 4-5ID021112Non-Confidential
Managing the firmware on your debug hardware unit3. Click Connect to connect to the debug hardware unit. Details of the existing firmware onthe unit are displayed. An example is shown in the following figure:Figure 4-3 Firmware details4. In the RVI Update utility, click the Install Firmware tool. The Select Firmware Updateto Install dialog box is displayed. An example is shown in the following figure:Figure 4-4 Selecting the component file to install5. Navigate to the directory containing the component file for the update or patch that youwant to install, and select the required file.6. Click Open. After a short delay, a dialog box appears that describes what is in thecomponent file, as shown in the following figure:ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 4-6ID021112Non-Confidential
Page 1 and 2: ®ARMDS-5Version 5.9Using the Debug
Page 3 and 4: Conformance NoticesThis section con
Page 5 and 6: Contents4.6 Restarting the debug ha
Page 7 and 8: Contents10.6 Auto Configure button
Page 9 and 10: Conventions and feedback• the ser
Page 11 and 12: Getting started with the debug hard
Page 19 and 20: Chapter 3Configuring network settin
Page 21 and 22: Configuring network settings for yo
Page 33 and 34: Managing the firmware on your debug
Page 35: Managing the firmware on your debug
Page 43 and 44: Chapter 5Creating debug hardware ta
Page 45 and 46: Creating debug hardware target conf
Page 87 and 88:
Creating debug hardware target conf
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128:
Using TraceConcepts• About using
Page 129 and 130:
Chapter 8Debugging with your debug
Page 131 and 132:
Debugging with your debug hardware
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Chapter 9Configuring debug hardware
Page 153 and 154:
Configuring debug hardware for GDB9
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?