ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Configuring network settings for your debug hardware unit3.3 The Configure Debug Hardware unit dialog boxThe Configure Debug Hardware unit dialog box enables you to modify the network settings ona debug hardware unit that has previously been configured. The following figure shows anexample:Figure 3-1 The Configure Debug Hardware unit dialog boxNoteYou can modify the settings only for a debug hardware unit that is on your local network or thatis connected to a USB port on your PC.The network settings available depend on whether or not your network uses Dynamic HostConfiguration Protocol (DHCP):• If your network uses DHCP, you must know:— the hostname that you want to use for your unit (if any)— the Ethernet type of your network.• If your network does not use DHCP, you must know:— the hostname that you want to use for your unit (if any)— the IP address that you want to use for your unit— the default gateway for your network (if it has one)— the subnet mask for your network.— the Ethernet type of your network.NoteThe Ethernet Address field is read-only.After setting up the network settings, click Configure to write the values to the unit.Click Exit to close the Configure Debug Hardware unit dialog box3.3.1 See alsoTasks• About configuring network settings on page 3-2• Determining the correct network settings on page 3-3• Configuring the network settings for a debug hardware unit on page 3-8• Modifying the network settings for a debug hardware unit on page 3-10• Troubleshooting on page 3-13.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 3-4ID021112Non-Confidential
Configuring network settings for your debug hardware unitReference• The Configure new Debug Hardware unit dialog box on page 3-6• Debug hardware unit network settings on page 3-7.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 3-5ID021112Non-Confidential
Page 1 and 2: ®ARMDS-5Version 5.9Using the Debug
Page 3 and 4: Conformance NoticesThis section con
Page 5 and 6: Contents4.6 Restarting the debug ha
Page 7 and 8: Contents10.6 Auto Configure button
Page 9 and 10: Conventions and feedback• the ser
Page 11 and 12: Getting started with the debug hard
Page 19 and 20: Chapter 3Configuring network settin
Page 21: Configuring network settings for yo
Page 25 and 26: Configuring network settings for yo
Page 33 and 34: Managing the firmware on your debug
Page 43 and 44: Chapter 5Creating debug hardware ta
Page 45 and 46: Creating debug hardware target conf
Page 73 and 74:
Creating debug hardware target conf
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128:
Using TraceConcepts• About using
Page 129 and 130:
Chapter 8Debugging with your debug
Page 131 and 132:
Debugging with your debug hardware
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Chapter 9Configuring debug hardware
Page 153 and 154:
Configuring debug hardware for GDB9
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?