ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Troubleshooting your debug hardware unit10.9.1 See alsoTasks• Autoconfiguring a scan chain on page 5-11• Adding devices to the scan chain on page 5-12.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 10-12ID021112Non-Confidential
Troubleshooting your debug hardware unit10.10 Log Client UtilityThe Log Client utility receives logging messages from a DSTREAM or RVI unit. The unit canbe connected over a network or USB.Output from all logging processes is displayed.10.10.1 Syntaxrvi_log_client rvi_unit_identifierrvi_log_client -helpwhere rvi_unit_identifier is the identifier for the RVI unit can be in any of the followingformats:IP Address Specify either:xxx.xxx.xxx.xxxTCP:xxx.xxx.xxx.xxxFor example, TCP:100.16.89.12HostnameUSBSpecify either:rvi_unit_nameTCP:rvi_unit_nameFor example, my-rvi-unit.Specify eitherUSBUSB:usb_port_numberusb_port_number is the number shown in the tree control or the scan chainschematic diagram of the Debug Hardware Config utility, for example:Figure 10-11 USB port number in the Debug Hardware Config utilityIn this example, the port number is 111410315.10.10.2 UsageSpecify -h or -help to display the help message and usage information.Press Ctrl+C to close the Log Client utility.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 10-13ID021112Non-Confidential
Page 1 and 2:
®ARMDS-5Version 5.9Using the Debug
Page 3 and 4:
Conformance NoticesThis section con
Page 5 and 6:
Contents4.6 Restarting the debug ha
Page 7 and 8:
Contents10.6 Auto Configure button
Page 9 and 10:
Conventions and feedback• the ser
Page 11 and 12:
Getting started with the debug hard
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 3Configuring network settin
Page 21 and 22:
Configuring network settings for yo
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Managing the firmware on your debug
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 5Creating debug hardware ta
Page 45 and 46:
Creating debug hardware target conf
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128:
Using TraceConcepts• About using
Page 129 and 130:
Chapter 8Debugging with your debug
Page 131 and 132:
Debugging with your debug hardware
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146: Debugging with your debug hardware
Page 151 and 152: Chapter 9Configuring debug hardware
Page 153 and 154: Configuring debug hardware for GDB9
Page 179 and 180: Configuring debug hardware for GDBO
Page 181 and 182: Configuring debug hardware for GDBR
Page 183 and 184: Configuring debug hardware for GDB
Page 185 and 186: Chapter 10Troubleshooting your debu
Page 187 and 188: Troubleshooting your debug hardware
Page 195: Troubleshooting your debug hardware
Page 199: Troubleshooting your debug hardware
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

Create successful ePaper yourself

Delete template?

Save as template?