ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Getting started with the debug hardware configuration utilitiesAny unit shown in light gray is one that has responded to browse requests but does nothave a valid IP address. You cannot connect to that unit by TCP/IP until you haveconfigured it for use on your network.Alternatively, connect the debug hardware unit directly to your PC using a USB cable.3. If multiple units are listed, and you are unsure about the debug hardware unit you want touse:a. Select a unit in the list, or enter an IP address of a unit on a different network.b. Click Identify. The identification indicators on the unit flash for five seconds.NoteOn RVI, all LEDs on the front panel flash during identification.On DSTREAM, the DSTREAM logo flashes during identification.4. To connect to your required unit, select the unit and click Connect. Alternatively, do oneof the following:• Double-click on the unit you want to connect to.• In the IP Address/Host Name field, enter either the IP address or host name of thedevice you want to connect to and click Connect.When a connection has been established, the configuration utility display changes to showthe configuration features provided by that utility.If you have problems connecting to a debug hardware unit, you must troubleshoot thedebug hardware connections.5. Select Exit from the File menu. This disconnects from any connected unit, and exits theconfiguration utility.2.5.3 See alsoTasks• Starting the debug hardware configuration utilities on page 2-3• Scanning for available debug hardware units on page 2-5• Scanning for available debug hardware units on page 2-5• Chapter 3 Configuring network settings for your debug hardware unit• Chapter 10 Troubleshooting your debug hardware unit.ReferenceSetting Up the ARM DSTREAM Hardware:• The DSTREAM unit on page 2-5.Setting Up the ARM RVI and RVT Hardware:• The RVI debug unit on page 2-10.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 2-9ID021112Non-Confidential
Chapter 3Configuring network settings for your debughardware unitThe following topics describe how to configure the network settings for your debug hardwareunit:• About configuring network settings on page 3-2• Determining the correct network settings on page 3-3• The Configure Debug Hardware unit dialog box on page 3-4• The Configure new Debug Hardware unit dialog box on page 3-6• Debug hardware unit network settings on page 3-7• Configuring the network settings for a debug hardware unit on page 3-8• Modifying the network settings for a debug hardware unit on page 3-10• Restarting your debug hardware unit on page 3-12• Troubleshooting on page 3-13.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 3-1ID021112Non-Confidential
Page 1 and 2: ®ARMDS-5Version 5.9Using the Debug
Page 3 and 4: Conformance NoticesThis section con
Page 5 and 6: Contents4.6 Restarting the debug ha
Page 7 and 8: Contents10.6 Auto Configure button
Page 9 and 10: Conventions and feedback• the ser
Page 11 and 12: Getting started with the debug hard
Page 17: Getting started with the debug hard
Page 21 and 22: Configuring network settings for yo
Page 33 and 34: Managing the firmware on your debug
Page 43 and 44: Chapter 5Creating debug hardware ta
Page 45 and 46: Creating debug hardware target conf
Page 69 and 70:
Creating debug hardware target conf
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128:
Using TraceConcepts• About using
Page 129 and 130:
Chapter 8Debugging with your debug
Page 131 and 132:
Debugging with your debug hardware
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Chapter 9Configuring debug hardware
Page 153 and 154:
Configuring debug hardware for GDB9
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

Create successful ePaper yourself

Delete template?

Save as template?