ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Configuring debug hardware for GDB9.20 rviload command syntaxrviload enables you to load a given binary file onto the target board through a specified debughardware unit.9.20.1 Syntaxrviload [options]... address:file [address:file]...address:file A raw binary file file to be loaded at the target memory address address inhexadecimal.--autoconfig=DELAYAutoconfigure the scan chain and then wait the number of seconds specified byDELAY.Option synonym: -a DELAY--checkCheck memory as it is being written.Option synonym: -c--devnum=DEVNUMThe JTAG scan chain device number (default 1). Device 0 refers to the debughardware unit, so you can only specify devices greater than 0.Option synonym: -d DEVNUM--help--host=HOST--jtagclockDisplay the command help.Option synonym: -hThe host IP address/name of the debug hardware unit.Option synonym: -H HOSTThe JTAG clock speed in Hz, 0==‘RTCK’ (default 10MHz).Option synonym: -s--jump=JUMPTOStart executing from this (hex) address after loading.Option synonym: -j JUMPTO--dccmode=MODEEnable debug communications in the particular MODE, and must be one of thefollowing:DCC Raw DCC through client. Raw (unprocessed) data exactly as it exitedthe DCC register on the target, and is fed to the client.DCP Raw DCC through TCP/IP port range from 5000. Raw data fed toTCP/IP port in the port range specified.VEC Virtual Ethernet/TTY with tty channel through client.VEP Virtual Ethernet/TTY with tty channel through port range from 5000.The DCC mode for rviload is specified by using a three-letter mode name such asVEP or VEC, whereas the DCC mode for rvigdbconfig is specified by a modenumber such as 0, 1 or 2.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 9-28ID021112Non-Confidential
Configuring debug hardware for GDBOption synonym: -m MODE--page=PAGE--quiet--rule=RULEThe target memory page number.Option synonym: -p PAGEDo not print any messages.Option synonym: -qTarget rule code.Option synonym: -r RULE9.20.2 ExamplesTo use the rviload utility from a Cygwin bash or Red Hat Linux shell, enter:$ rviload [option]... address:file [address:file]...For example:rviload --host=192.168.1.200 -s0 -j7300000 -mVEC -a0 7300000:C:\DEMOS\Linux_RVI_DCC\vp-boot.bin9.20.3 See alsoTasks• Setting DCC parameters on page 9-23.Reference• RVIahbload command syntax on page 9-30• RVIvec command syntax on page 9-32.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 9-29ID021112Non-Confidential
Page 1 and 2:
®ARMDS-5Version 5.9Using the Debug
Page 3 and 4:
Conformance NoticesThis section con
Page 5 and 6:
Contents4.6 Restarting the debug ha
Page 7 and 8:
Contents10.6 Auto Configure button
Page 9 and 10:
Conventions and feedback• the ser
Page 11 and 12:
Getting started with the debug hard
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 3Configuring network settin
Page 21 and 22:
Configuring network settings for yo
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Managing the firmware on your debug
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 5Creating debug hardware ta
Page 45 and 46:
Creating debug hardware target conf
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Configuring CoreSight systems6.1 Ab
Page 99 and 100:
Configuring CoreSight systems6.3 Co
Page 101 and 102:
Configuring CoreSight systems6.5 Ab
Page 103 and 104:
Configuring CoreSight systems6.7 Fo
Page 105 and 106:
Configuring CoreSight systems2. Loc
Page 107 and 108:
Configuring CoreSight systems• To
Page 109 and 110:
Configuring CoreSight systems6.10.1
Page 111 and 112:
Configuring CoreSight systemsName=T
Page 113 and 114:
Configuring CoreSight systemsName=T
Page 115 and 116:
Configuring CoreSight systems6.13.1
Page 117 and 118:
Configuring CoreSight systems6.15 C
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Chapter 7Using TraceThe following t
Page 125 and 126:
Using Trace7.2 Trace hardware captu
Page 127 and 128: Using TraceConcepts• About using
Page 129 and 130: Chapter 8Debugging with your debug
Page 131 and 132: Debugging with your debug hardware
Page 151 and 152: Chapter 9Configuring debug hardware
Page 153 and 154: Configuring debug hardware for GDB9
Page 177: Configuring debug hardware for GDB9
Page 181 and 182: Configuring debug hardware for GDBR
Page 183 and 184: Configuring debug hardware for GDB
Page 185 and 186: Chapter 10Troubleshooting your debu
Page 187 and 188: Troubleshooting your debug hardware
Page 199: Troubleshooting your debug hardware
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?