ARM DS-5 Using the Debug Hardware Configuration Utilities

More documents

Recommendations

Info

Configuring CoreSight systems6.10 Loading a trace association fileTo load a CoreSight trace association file:1. Open the Debug Hardware Config utility.2. Either:• connect to and configure a debug hardware connection to create a new debughardware configuration file• open an existing debug hardware configuration file.3. Click the Trace Associations... button to display the Trace Association Editor dialog box.The following figure shows an example:Figure 6-7 Trace Association Editor dialog boxThe devices shown reflect the order of those in the scan chain.4. Click Load... to display the Load RealView Associations File... dialog box.5. Locate the directory where you saved your trace association file.6. Click Open to load the file and return to the Trace Association Editor dialog box.7. Click OK to return to the Debug Hardware Config utility main window.An asterisk in a device box of the schematic diagram indicates that the device is associatedwith another device. The following figure shows that the CSETM and the Cortex-A8devices have associations:Figure 6-8 Devices with associationsARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 6-13ID021112Non-Confidential
Configuring CoreSight systems6.10.1 See alsoTasks• Starting the debug hardware configuration utilities on page 2-3• Setting up a CoreSight trace association file on page 6-11• Reading the CoreSight ROM table on page 6-3• CoreSight autodetection on page 6-4.Concepts• About CoreSight system configuration on page 6-2• How the debug hardware unit autodetects Serial Wire Debug on page 6-5• About trace associations on page 6-6.ARM DUI 0498F Copyright © 2010-2012 ARM. All rights reserved. 6-14ID021112Non-Confidential
Page 1 and 2:
®ARMDS-5Version 5.9Using the Debug
Page 3 and 4:
Conformance NoticesThis section con
Page 5 and 6:
Contents4.6 Restarting the debug ha
Page 7 and 8:
Contents10.6 Auto Configure button
Page 9 and 10:
Conventions and feedback• the ser
Page 11 and 12:
Getting started with the debug hard
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Chapter 3Configuring network settin
Page 21 and 22:
Configuring network settings for yo
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Managing the firmware on your debug
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Chapter 5Creating debug hardware ta
Page 45 and 46:
Creating debug hardware target conf
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58: Creating debug hardware target conf
Page 97 and 98: Configuring CoreSight systems6.1 Ab
Page 99 and 100: Configuring CoreSight systems6.3 Co
Page 101 and 102: Configuring CoreSight systems6.5 Ab
Page 103 and 104: Configuring CoreSight systems6.7 Fo
Page 105 and 106: Configuring CoreSight systems2. Loc
Page 107: Configuring CoreSight systems• To
Page 111 and 112: Configuring CoreSight systemsName=T
Page 113 and 114: Configuring CoreSight systemsName=T
Page 115 and 116: Configuring CoreSight systems6.13.1
Page 117 and 118: Configuring CoreSight systems6.15 C
Page 123 and 124: Chapter 7Using TraceThe following t
Page 125 and 126: Using Trace7.2 Trace hardware captu
Page 127 and 128: Using TraceConcepts• About using
Page 129 and 130: Chapter 8Debugging with your debug
Page 131 and 132: Debugging with your debug hardware
Page 151 and 152: Chapter 9Configuring debug hardware
Page 153 and 154: Configuring debug hardware for GDB9
Page 159 and 160:
Configuring debug hardware for GDB9
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Configuring debug hardware for GDBO
Page 181 and 182:
Configuring debug hardware for GDBR
Page 183 and 184:
Configuring debug hardware for GDB
Page 185 and 186:
Chapter 10Troubleshooting your debu
Page 187 and 188:
Troubleshooting your debug hardware
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199:
show all

ARM DS-5 Using the Debug Hardware Configuration Utilities

Create successful ePaper yourself

Delete template?

Save as template?