INSTALLATION MANUAL RC-2B RC-3B RC-4B RC-5B RC ... - Maxon
INSTALLATION MANUAL RC-2B RC-3B RC-4B RC-5B RC ... - Maxon INSTALLATION MANUAL RC-2B RC-3B RC-4B RC-5B RC ... - Maxon
INTRODUCTIONThis publication contains the information required to install the followingmodels and their options; RC, RCW, RCT, RC-CL, and RCHL from 2000to 6000 pound capacities. If there is any doubt in your mind regarding thesuitability of these lifts being installed on its intended vehicle, or any portionof these instructions that you do not understand, please contact the MaxonCustomer Service Department for consultation.Unauthorized modifi cation to this equipment may cause prematurefailure or create hazards in its use that are not foreseen at the time of theinstallation. These kinds of changes should be discussed with our EngineeringDepartment before being undertaken.Bed height requirements to ground are 38” laden to 56” unladen.These lifts cannot be installed on bodies with swing type doors.These lifts have been designed to fi t bodies that are 96” wide, (102”wide, in the case of the RCW Models). If this body has dimensions that aremuch different than these, special brackets will have to be fabricated forattachment. The corner posts of the body must also be made of steel so thatthe lift columns can be welded to it. If they are aluminum, then steel plateswill have to be fabricated to bolt to these corner posts for welding to the liftassembly. Both of the above conditions are rare and therefore have not beenprovided for in this manual. Contact the Customer Service Department if eitherof the above conditions exist.11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-77134
UNIT AS SHIPPEDDo not remove stands at bottom of column until instructed to do so.Steel box containing pump assembly, also contains a packinglist, instruction manuals, decals, and all necessary hardwareto complete installation.POWER UNIT BOXREINFORCEMENT ANGLE 8”COLUMN SUPPORT ANGLES 48”Two of these 18” angle iron pieces areto be used fi rst to assist in mountingthe lift to the truck, and then to supportthe pump box on trailer installations.The other two are welded to the columnsupport angles.11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713STANDBATTERY BOX ANDFRAME OPTIONPUMP BOXSTAND5
- Page 1 and 2: M-90-1REV. HOCTOBER 2012INSTALLATIO
- Page 3: Comply with the following WARNINGS
- Page 7 and 8: INSTALLATION OF UNIT - ContinuedCor
- Page 9 and 10: INSTALLATION OF UNIT - ContinuedTyp
- Page 11 and 12: WELDING TO FLATBEDThe column assemb
- Page 13 and 14: ATTACH OPTIONAL BATTERY BOX & FRAME
- Page 15 and 16: ATTACH OPTIONAL BATTERY BOX & FRAME
- Page 17 and 18: ATTACH OPTIONAL BATTERY BOX & FRAME
- Page 19 and 20: POWER PACK INSTALLATIONTRUCK BODIES
- Page 21 and 22: POWER PACK INSTALLATION - Continued
- Page 23 and 24: PUMP WIRING CAM CLOSERTOGGLESWITCH1
- Page 25 and 26: ADD HYDRAULIC FLUIDCAUTIONKeep dirt
- Page 27 and 28: FINAL ADJUSTMENTSFill the system wi
- Page 29 and 30: ATTACH DECALSNOTE: Ensure there is
- Page 31 and 32: OPTIONSRCT LIGHT INSTALLATIONALL RC
- Page 33 and 34: OPTIONSHAND PUMP OPTION FOR CAM CLO
- Page 35 and 36: RECOMMENDED LIFTGATE POWER CONFIGUR
- Page 37 and 38: FIXED RAMP INSTALLATION, 12”Lower
- Page 39 and 40: HINGED RAMP INSTALLATION (STEEL)7/8
UNIT AS SHIPPEDDo not remove stands at bottom of column until instructed to do so.Steel box containing pump assembly, also contains a packinglist, instruction manuals, decals, and all necessary hardwareto complete installation.POWER UNIT BOXREINFO<strong>RC</strong>EMENT ANGLE 8”COLUMN SUPPORT ANGLES 48”Two of these 18” angle iron pieces areto be used fi rst to assist in mountingthe lift to the truck, and then to supportthe pump box on trailer installations.The other two are welded to the columnsupport angles.11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713STANDBATTERY BOX ANDFRAME OPTIONPUMP BOXSTAND5