SG-4SIRN-___-___ 5-Button Wallstation with Infrared ... - Lutron

®TMWALLSTATIONSColor/Finish and Customizing InformationAdditional Informationrev addinfo-3a 9.04.01COLORS/FINISHMatte FinishesWhiteWHIvoryIV*BeigeBEGrayGR*BrownBRBlackBL* GR, IV not currentlybacklightedMetal Finishes(Standard with BlackPlastic Buttons)Bright Brass BBBright Chrome BCBright Nickel BNSatin Brass SBSatin Chrome SCSatin Nickel SNAntique Brass QBAntique Bronze QZGloss Finishes(Available with Insert (I) stylecontrols only; ship with Claro ® stylefaceplates)WhiteGWHLight Almond GLAAnodized AluminumClearCLABlackBLABrassBRABacklighting Notes:Illuminated text (translucent texton buttons) is available for thesecolors: BL and BR (also applies toall metal finishes).Illuminated buttons (with blacktext on buttons) are available forthese colors/finishes: WH, BE, GR,GWH*, GLA*.* Insert (I) style controls onlyMULTI-GANGING1. Order Insert (I) style controls.2. To order new Wallplates for multi-ganging, specify “R3”openings in a Lutron NovaT multi-gang FB (finsbroken) Series model number.Examples:Use Button Replacement Kits to change: colors, buttonconfiguration, engraving, between insert and non-insert versions.Non-Insert KitWallplate for 2 Seetouch Wallstations,Model # NT-R3-R3-FB-(color)Wallplate for other Lutron controls and 2Seetouch Wallstations,Model # NT-T8-R3-R3-FB-(color)Note: New button inserts are not included withmulti-ganging Wallplates.BUTTON REPLACEMENT KITSInsert KitEach Kit includesan adapter, buttonassembly, andwallplate® SPECIFICATION SUBMITTALPageJOB NAME:MODEL NUMBERS:JOB NUMBER:

®Wallstation InstallationDIP SWITCHES• Set DIP switches 1-4 to give the Wallstation the unique systemaddress from 1 to 16.• Set additional DIP switches (if any) to specify function asshown on the first page of the Wallstation’s SpecificationSubmittal.• Dip switch 10 controls the button backlight.DIP SWITCH SETTINGSAddress 1 2 3 4123456789TMWALLSTATIONSLOW-VOLTAGE CLASS 2 (PELV) WIRINGInstallationrev 3000-4000wallstation-4 9.04.01• Use low-voltage Class 2 (PELV) wiring to daisy-chain Wallstationsto Control Units and other components.• Make connections inside the wallbox. Or in a switchbox or junctionbox with a maximum wire length of 8 feet (2.5m) from thelink to the Wallstation.Note: EGRX Eurostyle Wallstations have a D terminal for Drain.You can connect the Drain/Shield at this terminal.When used with GRX-3000 Control Units• Two #18 AWG (1.0mm 2 ) conductors for common (terminal 1) and12VDC (terminal 2). Make sure you wire the the terminal 2 connectioncorrectly. Refer to GRX-3000 Specification Submittal.• One shielded, twisted pair #18 AWG (1.0mm 2 ) for data link (terminals3 and 4).When used with GRX-4000 Control Units• Two #12 AWG (2.5mm 2 ) conductors for common (terminal 1) and24VFW (terminal 2). These won’t fit in terminals. Connect asshown.• One shielded, twisted pair #18 AWG (1.0mm 2 ) for data link (terminals3 and 4).• Connect Drain/Shield as shown.- Do not connect to Ground (Earth) or Wallstation.- Connect the bare drain wires and cut off the outside shield.10111213Wallstation Rear ViewData Link(1) Shielded, twistedpair #18 AWG (1.0mm 2 )3: MUX4: MUX141516Reserved for GRX-PRG, if present on link.4321(1) #18 AWG(1.0mm 2 )D: Drain/Shield(2) #12 AWG(2.5mm 2 )(1) #18 AWG(1.0mm 2 )(2) #12 AWG(2.5mm 2 )Class 2/PELVControl Wiring1: Common2: 24VFW® SPECIFICATION SUBMITTALPageJOB NAME:MODEL NUMBERS:JOB NUMBER: