ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 13: Tail Section Installation Step 8Mix up 1/2-ounce (15Ml) of 30-minute epoxy. Apply theepoxy to the exposed wood of the stabilizer. The stabilizershould then be bolted into place. Refer to Step 4 fordetails Use paper towels and rubbing alcohol to removeany excess epoxy from the fuselage and stabilizer. Allowthe epoxy to fully cure before proceeding. Step 10Use a drill and 1/16-inch (1.5mm) drill bit to drill thelocations for the servo mounting screws. Step 9Position the servo in the opening with the servo armfacing the front of the fuselage. Mark the locations for theservo mounting screws using a felt-tipped pen. Step 11Apply a few drops of thin CA to each of the holes drilledin the previous step. This will help harden the wood,making the screws more secure in their placement.66
Section 13: Tail Section Installation Step 12Secure the elevator servo in the fuselage using thehardware provided with the servo. Step 14Connect the pushrod to the servo arm as shown. Step 13Remove the supplied servo arm from the servo. Cutone arm from a medium-length servo arm so it won'tinterfere with the operation of the elevator. Secure thearm to the output of the elevator servo. Use a felt-tippedpen to mark the pushrod where it crosses the outer holeof the servo arm.Note: It may be necessary to bend the elevatorpushrod slightly to align with the servo arm.67
Page 1:
B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6:
Recommended JR, JR SPORT and Spektr
Page 7:
Contents of Kit and Replacement Par
Page 10 and 11:
Safety, Precautions, and WarningsTh
Page 12 and 13:
Section 1: Hinging the Flaps and Ai
Page 14 and 15:
Section 2: Aileron Servo Installati
Page 16 and 17: Section 2: Aileron Servo Installati
Page 18 and 19: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air
show all

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?