ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 12: Rudder and Servo Installation Step 5Mount the servo cover using four #2 x 3/8-inch sheetmetal screws. Step 7Use 30-minute epoxy to attach the fin to the stabilizer.90-degrees Step 6Use a sharp hobby knife to remove the covering from thefin where the tab from the stabilizer will be inserted.Note: Make sure the vertical fins remainin alignment while the epoxy cures. Step 8Remove the elevators and rudders from the stabilizer andfins and set aside the CA hinges.60
Section 12: Rudder and Servo Installation Step 9Use a rotary tool and 1/16-inch (1.5mm) drill bit to drilla 1/2-inch (12mm) deep hole in the center of each hingeslot for the rudders and fins. This provides a tunnelallowing the glue used to secure the hinges to fullypenetrate the hinge. Step 12Slide the rudder into position on the fin. Make sure therudder can move without binding against the fin at the topand bottom.Note: Drill the holes in the hinge slots for theelevators and stabilizer at this time as well. Step 10Place a T-pin in the center of each of the twelve hinges. Step 13Remove the T-pins from the hinge and push the ruddertight against the fin. Flex the rudder and apply enoughthin CA to fully penetrate the hinge. Apply CA to bothsides of the hinge. Step 11Slide the hinges back into the rudder. The T-pin will keepthe hinge centered evenly in the rudder and fin when therudder is installed.Important: Do not use accelerator whenhinging. The CA must be allowed to soakinto the hinge for the best possible bondbetween the hinge and surrounding wood.61
Page 1:
B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6:
Recommended JR, JR SPORT and Spektr
Page 7:
Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air
show all

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?