ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 11: Wing Installation Step 5Use a wing bolt to keep the plate aligned at the first holeand mark the location for the second hole on the plate.Note: The Step 7 is for the EP versiononly. Skip to Step 8 when buildingthe glow powered version. Step 7When building an EP version of your B-<strong>25</strong>, attach thebatteries to the battery tray with hook and loop straps. Thetray keys into the former at the front, and is secured at therear using the wing bolts, with the wing bolt plate betweenthe wing and plate. Step 6Attach the wing using the wing bolt plate and two 1/4-20x 1 1 / 2-inch socket head bolts and two 1/4-inch washers.Use a 3/16-inch ball driver to tighten the wing bolts. Step 8Fasten the belly hatch in position.58
Section 12: Rudder and Servo InstallationRequired Parts• Stabilizer • Nylon clevis (2)• Pushrod connector (2) • Control horn (2)• Servo w/hardware (2)• Rudder (right and left)• Rudder linkage, 2-inch (51mm) (2)• 2-56 x 7/8-inch machine screw (6)• #2 x 3/8-inch sheet metal screw (8) Step 3Use a drill and 1/16-inch (1.5mm) drill bit to drill fourholes, approximately 1/8-inch (3mm) from the corners ofthe servo cover.Required Tools and Adhesives• Drill• Thin CA• Phillips screwdriver • Long servo arm• Hobby knife• Felt-tipped pen• Pliers• Drill bit: 1/16-inch (1.5mm), 5/32-inch (2mm) Step 1Mounting the rudder servo follows the same procedureas mounting the aileron servo (Section 2: Aileron ServoInstallation, Steps 1 through 7.) Use a 180 degree servoarm and remove the excess arm using side cutters. Simplyfollow those steps to mount the rudder servo to the rudderservo cover. Step 4Apply a few drops of thin CA to each of the holes toharden the surrounding wood. Step 2Route the servo lead to the nearest hole in the center ofthe stabilizer using the installed string. Position the coverso the servo arm is toward the tip of the stabilizer.59
Page 1:
B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6:
Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air
show all

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?