ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 8: Retractable Landing Gear Installation Step 21From the back side of the mounting rails, insert thefour 4-40 blind nuts and use a 4-40 bolt with a washerto draw each blind nut into each one of the four holesjust drilled. Step 23Set the main gear retract onto the mounting rails. Placea # 4 washer onto each of the four 4-40 x 1-inch sockethead bolts, then securely fasten the retract to the mountingrails with these four 4-40 x 1-inch bolts. Step 22Install 20-inch (508mm) of each color of air line ontoeach air cylinder inlet on the main landing gear. These airlines will be pulled later through the same holes in thewing that the throttle servo leads are pulled through. Becertain to follow the included Robart air line diagram forthe correct hook-up of the colored air lines.50
Section 8: Retractable Landing Gear Installation Step 24Route the air lines from the retract unit through the nacelleloosely. If you are installing the retracts and the wingextensions are already in place, then you will need to usea string and a weight to fish the air lines through the wing.Both sets of these air lines will be hooked up later usingthe Robart air installation diagram which we have includedon page 73 of this manual) Step <strong>25</strong>Install the main wheel onto a wheel axle and then installtwo #10 washers onto the axle before inserting the wheeland axle into the strut. The washers act as spacers to keepthe wheel from rubbing against the strut leg. Temporarilytighten the setscrew and then cut off the excess axle usinga rotary tool and cutoff wheel. File a flat area on the axlefor the wheel strut setscrew and then install the wheel andaxle to the main wheel strut. Step 26Repeat Steps 17 through <strong>25</strong> for the remaining main gear.Note: Use threadlock on all screws to keepthem from coming loose during flight.51
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?