ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 8: Retractable Landing Gear Installation Step 14Center the nose gear and steering servo. Thread a clevison the threaded rigging couplers and attach them to thesteering servo arm. Make sure to cut a 1/4-inch (4mm)piece of heat shrink tubing for each of the clevises andslide them into position. Mark where the cable crosses thehole in the fastener. Step 16Use a rotary tool and sanding drum to remove the areaof the nose gear cover to allow the nose wheel strut andwheel to pass through. Step 15Repeat the crimping process, aligning the marks madeon the cable with the hole in the fastener. Cut any excesscable using side cutters.Note: Use the same color air line forup and then use the same other colorfor down on each of the three retractunits. This will allow you to follow theincluded air line diagram from Robart.Note: Use threadlock on all screws to keepthem from coming loose during flight.48
Section 8: Retractable Landing Gear Installation Step 17We installed a rubber band to help hold the pull/pullcables clear of the nose wheel and strut when it isretracted/extended. Make a small plywood bracket with asmall opening in the end for the rubber band and glue thebracket to the floor of the retract wheel well. Step 19Set the main gear onto the mounting rails and mark themounting hole locations.Main Gear Installation Step 20Remove the retract unit from the mounting rails and drill a9/64-inch (4mm) hole on each of the marks. Step 18The nacelles have an outline on them showing the areathat needs to be removed to allow the struts to retract upinto the nacelle. Use a rotary tool and a sanding drum toremove this area to allow the retract strut and wheel topass through.49
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

Create successful ePaper yourself

Delete template?

Save as template?