ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 8: Retractable Landing Gear Installation Step 7Set the nose gear retract onto the mounting rails. Placea # 4 washer onto each of the four 4-40 x 1-inch sockethead bolts, then securely fasten the retract to the mountingrails with these four 4-40 x 1-inch bolts Step 8Install the nose wheel onto a wheel axle and then installtwo #10 washers onto the axle before inserting the wheeland axle into the strut. The washers act as spacers to keepthe wheel from rubbing against the strut leg. Temporarilytighten the setscrew and then cut off the excess axle usinga rotary tool and cutoff wheel. File a flat area on the axlefor the wheel strut setscrew and then install the wheel andaxle to the nose wheel strut. We used a couple of washersbetween the wheel and the strut to keep the wheel fromrubbing on the strut. Step 9Cut two 12-inch (305mm) lengths of pull-pull wire forthe steering. Connect the pull-pull cable to the steeringarm using two crimps. Pass the cable through a crimp,through the fasteners then back through the crimp. Usecrimping pliers to secure the crimps on the wire.Important: Use threadlock onany metal-to-metal fasteners.46
Section 8: Retractable Landing Gear Installation Step 10Remove the standard servo arm and attach a large180-degree standard arm on the servo. Position theservo in the opening with the servo arm facing the rearof the fuselage. Mark the locations for the servo mountingscrews using a felt-tipped pen. Step 12Apply a few drops of thin CA into each hole to harden thesurrounding wood. You may need to run the drill bit backthrough the holes after applying the CA. Step 11Use a drill and 1/16-inch (1.5mm) drill bit to drill thelocations for the servo mounting screws. Step 13Use the servo hardware that came with your servo tosecure the steering servo in the fuselage.47
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?