ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 7: Fixed Landing Gear InstallationNote: Use threadlock on all four ofthe 3mm nuts to prevent vibrationsfrom loosening them. Step 13Remove the standard servo arm and attach a large180-degree standard arm on the servo. Position theservo in the opening with the servo arm facing the rearof the fuselage. Mark the locations for the servo mountingscrews using a felt-tipped pen. Step 15Apply a few drops of thin CA into each hole to harden thesurrounding wood. You may need to run the drill bit backthrough the holes after applying the CA. Step 16Use the servo hardware to secure the steering servoin the fuselage. Step 14Use a drill and 1/16-inch (1.5mm) drill bit to drill thelocations for the servo mounting screws.42
Section 7: Fixed Landing Gear Installation Step 17Connect the pull-pull cable to the steering arm usingtwo crimps. Pass the cable through a crimp, throughthe fasteners then back through the crimp. Use crimpingpliers to secure the crimps on the wire. Step 19Repeat the crimping process, aligning the marks madeon the cable with the hole in the fastener. Cut any excesscable using side cutters. Step 18Center the nose gear and steering servo. Thread a clevison the threaded rigging couplers and attach them to thesteering servo arm. Make sure to cut a 1/4-inch (4mm)piece of heat shrink tubing for each of the clevises andslide them into position. Mark where the cable crosses thehole in the fastener. Step 20Place the doors in position and drill a 1/16-inch(1.5mm) hole 1/8-inch (3mm) from the corners of thesteering servo and nose gear doors. Remove doors andapply a few drops of thin CA into each hole of the doorsand the mounting tabs in the fuselage to harden thesurrounding wood. Step 21Secure the doors over the steering servo and nose gearwith eight #2 x 3/8-inch sheet metal screws at each cornerof the doors.43
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

Create successful ePaper yourself

Delete template?

Save as template?