ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 7: Fixed Landing Gear Installation Step 4Slide the main gear into the engine nacelle. Step 6Enlarge the holes in the gear rails ONLY using a 7/64-inch(3mm) drill bit.Note: Wheel not shown for clarity. Step 5Use a drill and 5/64-inch (2mm) drill bit to drill fourholes through the mounting rails and into the gearblock. these holes are to be drilled 1/2-inch (13mm) andthen 1 1 / 2-inch (38mm) from the front of the rear bulkhead.The holes are to be centered on the rails. By doing thisyou can later use the same holes to install the optionalretracts. Step 7Secure the main gear in the engine nacelle using four#4 x 1-inch sheet metal screws. Step 8Repeat Steps 1 through 7 to install the remaining maingear in the engine nacelle.40
Section 7: Fixed Landing Gear Installation Step 9Slide the steering arm onto the nose gear wire. Next,slide the mount on the wire, then a wheel collar. Thesteering arm and wheel collar have setscrews that willtighten onto the flat areas that have been pre-ground onthe nose gear wire. Step 11Prepare four 3mm x <strong>25</strong>mm machine screws by sliding a3mm washer on each screw. Slide the screws through thenose gear mount, then slide the tapered block onto thescrews. The wider section of the block will be away fromthe steering arm. This tapered block creates the forward105-degree rake of the nose gear.Note: Make sure to use threadlock on thesetscrews for the steering arm and wheel collar. Step 10Install the rigging coupler in the steering arm as shown. Step 12Position the nose gear assembly in the fuselage and usefour 3mm washers and 3mm nuts to secure the nose gearin the fuselage.41
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

Create successful ePaper yourself

Delete template?

Save as template?