ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 6: Glow Engine Installation Step 24We used a fuel dot on the line to the needle valve that willmount to the cowling, making fueling the engine mucheasier when the cowl has been installed. When using afuel dot you will need to splice a "T" fitting between thetank and the carburetor as shown. Step 26Use hobby scissors and a rotary tool with a small sandingdrum to make a round opening in the dummy engine forthe motor shaft. Step <strong>25</strong>Connect the lines from the tank to the engine. Step 27Use a sharp hobby knife to remove the materialbetween the dummy cylinder heads to allow coolingair to pass through the dummy engine and over themotor. Use 30-minute epoxy to glue the dummy engineinside the cowling.Note: Do not remove the area between allof the dummy cylinder heads. You need toonly remove the area in front of and nextto the glow engine. This will help maintainairflow over the engine cylinder head andhelp to promote proper engine cooling.36
Section 6: Glow Engine Installation Step 28Tape four pieces of card stock to the engine nacelle. Alignthe card stock so the ends align with the front edge of thefirewall. Align the length so it is aligned with the raisedareas of the nacelle. Step 30Drill four locations for the mounting screws using a1/16-inch (1.5mm) drill bit. Drill the holes centeredin the card stock and roughly 1/8-inch (3mm) backfrom the end of the template to guarantee drilling intothe hardwoood positioned behind the raised areas ofthe nacelle. Step 29Slide the cowling onto the nacelle and align theopening in the dummy engine with the propeller adapterof the engine. Step 31Apply a few drops of thin CA to each of the holes drilledin the previous step. This will help harden the wood,making the screws more secure in their placement.37
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?