ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Section 6: Glow Engine Installation Step 7Attach the engine to the engine mount using four4-40 x 1-inch socket head screws, four #4 washersand four 4-40 locknuts. The included engine mount isdrilled for the Evolution 36NT. Step 9Slide the pushrod into the pushrod tube. Secure theengine mount to the firewall using four 8-32 x 1 1 / 4-inchsocket head bolts and four #8 washers. Bend the pushrodwire slightly so it moves freely inside the pushrod tubeand will clear the muffler.Note: The distance from the rear of themount to the front edge of the drive washerwill be 4 3 / 16-inch (107mm). Using anengine other than the Evolution enginemay required drilling new holes in themount for the engine mounting screws. Step 10Use a pin drill and 5/64-inch (2mm) drill bit to enlarge thehole in the throttle servo arm. Step 8Pass the Z-bend of the throttle pushrod into the carburetorarm.32
Section 6: Glow Engine Installation Step 11Slide the pushrod connector into the hole. Step 14Position the servo in the opening with the servo armfacing the rear of the necelle. Mark the locations for theservo mounting screws using a felt-tipped pen. Step 12Secure the connector using a 2mm washer and C-clip. Step 15Use a drill and 1/16-inch (1.5mm) drill bit to drill thelocations for the servo mounting screws. Step 13Remove the excess arms from the servo horn. Center thethrottle servo and attach the arm to the servo.33
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 10 and 11: Safety, Precautions, and WarningsTh
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 34 and 35: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61: Section 12: Rudder and Servo Instal
Page 62 and 63: Section 12: Rudder and Servo Instal
Page 64 and 65: Section 13: Tail Section Installati
Page 66 and 67: Section 13: Tail Section Installati
Page 68 and 69: Section 14: Receiver, Battery and S
Page 70: Section 14: Receiver, Battery and S
Page 73 and 74: Control ThrowsThe amount of control
Page 75 and 76: Pre-FlightCharge both the transmitt
Page 77 and 78: Engine OutA concern that most pilot
Page 79 and 80: 2007 Official AMANational Model Air

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?