ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

More documents

Recommendations

Info

Safety, Precautions, and WarningsThis model is controlled by a radio signal that is subject to interference from many sources outside your control. Thisinterference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions aroundyour model, as this margin will help to avoid collisions or injury.• Always operate your model in an open area away from cars, traffic, or people.• Avoid operating your model in the street where injury or damage can occur.• Never operate the model into the street or populated areas for any reason.• Never operate your model with low transmitter batteries.• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeablebattery packs, etc.) that you use.• Keep all chemicals, small parts and anything electrical out of the reach of children.• Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protectedfor this purpose.10
Section 1: Hinging the Flaps and AileronsRequired Parts• Wing panel w/ailerons & flaps (right and left)Required Tools and Adhesives• Rotary tool• T-pins• Drill bit: 1/16-inch (1.5mm) • Thin CA• 30-minute epoxy• Mixing stick• Mixing cup Step 3Place a T-pin in the center of each of the eight hingesremoved in Step 1. Step 1Remove the flaps and aileron from the wing panel and setaside the CA hinges. Step 4Slide the hinges back into the aileron. The T-pin will keepthe hinge centered evenly in the aileron and wing whenthe aileron is installed. Step 2Use a rotary tool and 1/16-inch (1.5mm) drill bit to drilla 1/2-inch (12mm) deep hole in the center of each hingeslot. This provides a tunnel allowing the glue used tosecure the hinges to fully penetrate the hinge.11
Page 1: B-25 Mitchell ARFAssembly manualSpe
Page 5 and 6: Recommended JR, JR SPORT and Spektr
Page 7: Contents of Kit and Replacement Par
Page 12 and 13: Section 1: Hinging the Flaps and Ai
Page 14 and 15: Section 2: Aileron Servo Installati
Page 20: Section 3: Fixed Flap Linkage Insta
Page 23 and 24: Section 4: Operation Flap Linkage I
Page 25 and 26: Section 4: Operation Flap Linkage I
Page 27 and 28: Section 5: Electric Motor Installat
Page 29: Section 5: Electric Motor Installat
Page 32 and 33: Section 6: Glow Engine Installation
Page 40 and 41: Section 7: Fixed Landing Gear Insta
Page 42 and 43: Section 7: Fixed Landing Gear Insta
Page 44 and 45: Section 8: Retractable Landing Gear
Page 52 and 53: Section 9: Retract Valve and Hardwa
Page 54 and 55: Section 10: Engine Nacelle Installa
Page 56 and 57: Section 10: Engine Nacelle Installa
Page 58 and 59: Section 11: Wing Installation Step
Page 60 and 61:
Section 12: Rudder and Servo Instal
Page 62 and 63:
Section 12: Rudder and Servo Instal
Page 64 and 65:
Section 13: Tail Section Installati
Page 66 and 67:
Section 13: Tail Section Installati
Page 68 and 69:
Section 14: Receiver, Battery and S
Page 70:
Section 14: Receiver, Battery and S
Page 73 and 74:
Control ThrowsThe amount of control
Page 75 and 76:
Pre-FlightCharge both the transmitt
Page 77 and 78:
Engine OutA concern that most pilot
Page 79 and 80:
2007 Official AMANational Model Air
show all

ASSEMBLY MANUAL B-25 Mitchell ARF - RC DEPOT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?