Pipet-Plus - Mettler Toledo

More documents

Recommendations

Info

Pipet-Plus StoragePipet-Plus is a precision instrument and should be treated withthe level of care appropriate for laboratory instrumentation.After use, store it in a clean safe place. Three types of hangerare available to hold your Pipet-Plus conveniently when not inuse.CR-7:Free-standing carousel holds seven pipettes.HU-M3: Set of three individual magnetic Hang-Ups formounting on ferrous surfaces.HU-S3:Three Hang-Ups attached to a clamp which fits ontoa shelf.Troubleshooting and RepairsWarning: When removing the shaft from the body, makesure the spring, seal and o-ring do not fall off the piston,especially on the smaller models.Sample Splash (liquid inside the mechanism)1. Refer to Figure 4 (p. 6) to remove the tip ejector arm.2. On pipettes up to 1000 µL, unscrew the shaft couplingand remove the shaft. For 2000 µL, unscrew the shaft. For5000 µL and 10 mL, unscrew the lower part of the shaft.3. Inspect the seal assembly and piston for contamination. Thepiston should be shiny and free of corrosion. Clean with distilledwater or isopropyl alcohol. Dry with a lint-free tissue,inspect the interior of the shaft for any contamination, andreassemble.4. If any staining and/or corrosion of the piston is evident, donot use the instrument. Call Pipette Service 800-662-7027.Leaks, Inaccurate Sampling, Abnormal Stroke1. Loose shaft. Tighten coupling by hand.2. Split or cracked shaft. Remove the tip ejector and inspectthe shaft. Replace the shaft if necessary. If the shaft wasdropped, remove it to see if the piston is bent. If so, return theinstrument for service.3. Worn seal and / or o-ring. Most models incorporate apolyethylene seal and o-ring. Examine the seal and o-ring,replacing them as necessary. Pull off the old seal and o-ring, position the new seal and o-ring on the piston assemblyas shown in the line drawings on pages 10-11, andreassemble Pipet-Plus.4. Do not lubricate any components* Pipet-Plus uses a drysealing system (*except for the 5000 and 10 mL modelswhich use a grease seal.)8
Service, Calibration and RepairRAININ Pipette Repair and Calibration facilities:California:7500 Edgewater Drive, Oakland CA 94621Tel. 800-662-7027, Fax 510-564-16835955 Mira Mesa Blvd, Ste B, San Diego, CA 92121Tel. 800-662-7027, Fax 858-320-0556Massachusetts: Rainin Road, Woburn, MA 01801Tel. 800-662-7027, Fax 781-935-7631Japan: 4-1-11, Bunkyo-Ku, Tokyo 113-0033Tel. (03) 5689-8311, Fax (03) 5689-2670METTLER TOLEDO Pipette Repair and Calibration facilities:Belgium: N.V. Mettler-Toledo s.a., B-1932 ZaventemTel. (02) 334 02 11, Fax (02) 334 03 34Germany: Mettler-Toledo GmbH, D-35353 GiessenTel. (0641) 50 70, Fax (0641) 507 128Denmark: Mettler-Toledo A/S, DK-2600 GlostrupTel. (43) 270 800, Fax (43) 270 828Spain: Mettler-Toledo S.A.E., E-08038 BarcelonaTel. (93) 223 76 00, Fax (93) 223 02 71France: HTS – F28000 ChartresTel. (02) 37 88 31 00, Fax (02) 37 88 31 09Italy: Mettler-Toledo S.p.A., I-20026 Novate MilaneseTel. (02) 333 321, Fax (02) 356 29 73Netherlands: Mettler-Toledo B.V., NL-4004 JK TielTel. (0344) 63 83 63, Fax (0344) 63 83 90Sweden: Mettler-Toledo AB, S-12008 StockholmTel. (08) 702 50 00, Fax (08) 642 45 62Service is also available in many other countries through authorizedRAININ distributors. See www.rainin-global.com.It is recommended to use only genuine RAININ replacement partssuch as seals and shafts. It is NOT necessary to recalibrate thepipette after changing the seal or shaft. Recalibration of the pipetteis only necessary when the piston is replaced, and should be doneonly by qualified factory-trained personnel in one of the abovementionedfacilities.For pipettes under warranty, please note that the warrantywill be voided if the pipette has been damaged as a resultof physical or chemical abuse, or if the pipette has beenrepaired or recalibrated by any service facility which is notauthorized by Rainin.Contact Technical Support at 800-543-4030 for furtherinformation.9
Page 1 and 2: Pipet-PlusLatch-Mode Pipettecontin
Page 3 and 4: IntroductionRAININ Pipet-Plus pipet
Page 5 and 6: Example volumes for the 200 µL siz
Page 7 and 8: ABA Press plunger button fully(blow
Page 9: Mixing (recommended only above 15%
Page 13 and 14: Pipet-Plus 1000 µL Pipet-Plus 2000
Page 15 and 16: SpecificationsThese manufacturer’

Pipet-Plus - Mettler Toledo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?