Cisco Small Business RV 120W Wireless-N VPN Firewall ...

More documents

Recommendations

Info

Configuring NetworkingConfiguring IPv62• 6 to 4 Tunnel—Uses the tunnel interface to route traffic from an IPv6 networkto other IPv6 networks over an IPv4 network.STEP 8Enter the IP Address of the gateway through which the destination host or networkcan be reached.STEP 9 In the metric field, specify the priority of the route by choosing a value between 2and 15. If multiple routes to the same destination exist, the route with the lowestmetric is used.STEP 10 Click Save.Configuring TunnelingThe Cisco RV120W provides several IPv6 tunneling methods. 6to4 tunnelingallows IPv6 packets to be transmitted over an IPv4 network. 6to4 tunneling istypically used when a site or end user wants to connect to the IPv6 Internet usingthe existing IPv4 network.NOTEYou must use static routes when tunneling. See Configuring Static Routing,page 46.To configure 6to4 Tunneling:STEP 1STEP 2STEP 3Select Networking > IPv6 > Tunneling.Check the Automatic Tunneling box.Click Save.Viewing IPv6 Tunnel InformationTo view IPv6 tunnel information, choose Networking > IPv6 > Tunneling. ClickRefresh to get the latest information.The IPv6 Tunnel Status table shows the name of tunnel and the IPv6 address thatis created on the device.Cisco RV120W Administration Guide 47
Configuring NetworkingConfiguring IPv62Configuring Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)TunnelsIntra-site automatic tunnel addressing protocol (ISATAP) is a method to transmitIPv6 packets between dual-stack nodes over an IPv4 network. The CiscoRV120W is one endpoint (a node) for the tunnel. You must also set a local endpoint,as well as the ISATAP Subnet Prefix that defines the logical ISATAP subnet toconfigure a tunnel.To add an ISATAP tunnel:STEP 1STEP 2STEP 3STEP 4STEP 5STEP 6STEP 7Choose Networking > IPv6 > Tunneling.In the ISATAP Tunnel Table, click Add.Enter the tunnel name.Choose the local endpoint address, or the endpoint address for the tunnel thatstarts with the Cisco RV120W. The endpoint can be the LAN interface (if the LANis configured as an IPv4 network), or another LAN IPv4 address.If you chose Other IP in Step 4, enter the IPv4 address of the endpoint.Enter the ISATAP subnet prefix. This is the 64-bit subnet prefix that is assigned tothe logical ISATAP subnet for this intranet. This can be obtained from your ISP orinternet registry, or derived from RFC 4193.Click Save.To modify the settings of an ISATAP tunnel:STEP 1STEP 2STEP 3Choose Networking > IPv6 > Tunneling.Check the check boxes for the tunnels you want to modify.Click Edit, make the changes, and click Save.Cisco RV120W Administration Guide 48
Page 1 and 2:
ADMINISTRATIONGUIDECisco Small Busi
Page 4 and 5:
ContentsChapter 2: Configuring Netw
Page 6 and 7: ContentsChapter 4: Configuring the
Page 8 and 9: ContentsConfiguring Network Managem
Page 10 and 11: 1IntroductionThis chapter describes
Page 12 and 13: IntroductionProduct Overview1Securi
Page 14 and 15: IntroductionGetting to Know the Cis
Page 16 and 17: IntroductionMounting the Cisco RV12
Page 18 and 19: IntroductionConnecting the Equipmen
Page 20 and 21: IntroductionConnecting the Equipmen
Page 22 and 23: IntroductionUsing the Getting Start
Page 24 and 25: IntroductionNavigating through the
Page 26 and 27: IntroductionSaving Your Changes1Sav
Page 28 and 29: 2Configuring NetworkingThe networki
Page 30 and 31: Configuring NetworkingConfiguring t
Page 44 and 45: Configuring NetworkingConfiguring R
Page 47 and 48: Configuring NetworkingConfiguring R
Page 49 and 50: Configuring NetworkingConfiguring P
Page 51 and 52: Configuring NetworkingConfiguring I
Page 55: Configuring NetworkingConfiguring I
Page 59 and 60: Configuring NetworkingConfiguring I
Page 61 and 62: Configuring the Wireless NetworkA N
Page 63 and 64: Configuring the Wireless NetworkUnd
Page 65 and 66: Configuring the Wireless NetworkCon
Page 75 and 76: Configuring the FirewallCisco RV120
Page 77 and 78: Configuring the FirewallConfiguring
Page 97 and 98: Configuring the FirewallFirewall Co
Page 99 and 100: Configuring the FirewallFirewall Co
Page 101 and 102: 5Configuring Virtual Private Networ
Page 103 and 104: Configuring Virtual Private Network
Page 105 and 106: Configuring Virtual Private Network
Page 107 and 108:
Configuring Virtual Private Network
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
6Configuring Quality of Service (Qo
Page 123 and 124:
Configuring Quality of Service (QoS
Page 125 and 126:
Configuring Quality of Service (QoS
Page 127 and 128:
Administering Your Cisco RV120WConf
Page 129 and 130:
Administering Your Cisco RV120WUsin
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Administering Your Cisco RV120WCapt
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Administering Your Cisco RV120WUpgr
Page 145 and 146:
8Viewing the Cisco RV120W StatusThi
Page 147 and 148:
Viewing the Cisco RV120W StatusView
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
AUsing Cisco QuickVPN for Windows 7
Page 161 and 162:
Using Cisco QuickVPN for Windows 7,
Page 163:
BWhere to Go From HereCisco provide
show all

Cisco Small Business RV 120W Wireless-N VPN Firewall ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?