Cisco Small Business RV 120W Wireless-N VPN Firewall ...

More documents

Recommendations

Info

Administering Your Cisco RV120WConfiguring Logging7Configuring Email LoggingSTEP 1STEP 2Choose Administration > Logging > Remote Logging Configuration.Select the check box to enable e-mail logs. Then enter the following:• E-mail Server Address—Enter the IP address or Internet Name of an SMTPserver. The router will connect to this server to send e-mail logs whenrequired.• SMTP Port—Configure the port to connect smtp server.• Return E-mail Address—Enter the e-mail address where the replies fromthe SMTP server are to be sent (required for failure messages).• Send To E-mail Address(1)—Enter the e-mail address where the logs andalerts are to be sent.• Send To E-mail Address(2)—Enter the e-mail address where the logs andalerts are to be sent.• Send To E-mail Address(3)—Enter the e-mail address where the logs andalerts are to be sent.• Authentication with SMTP server—If the SMTP server requiresauthentication before accepting connections, select either Login Plain orCRAM-MD5 and enter the Username and Password to be used forauthentication. To disable authentication, select None.• Respond to Identd from SMTP Server—Check this box to configure therouter to respond to an IDENT request from the SMTP server.STEP 3STEP 4To confirm that the e-mail logs function is configured correctly, press Test.(Optional) To receive e-mail logs according to a schedule, configure theappropriate schedule settings:• Unit—Select the period of time that you need to send the log: Hourly, Daily,or Weekly. To disable sending of logs, select Never. This option is usefulwhen you do not want to receive logs by e-mail, but want to keep e-mailoptions configured so that you can use the Send Log function from theStatus > View Logs pages.• Day—If logs are to be sent on a weekly basis, choose the day of the week.• Time—Select the time of day when logs should be sent.Cisco RV120W Administration Guide 129
Administering Your Cisco RV120WConfiguring the Discovery Settings7STEP 5STEP 6STEP 7Under Logging Policy, choose the type of logging policy. (See ConfiguringLogging Policies, page 127.) By default, only IPsec VPN logs are enabled. Othersare disabled.If you want the router to send logs to a Syslog server, check the box next to asyslog server field and enter the IP address or Internet Name of the Syslog serverin the Syslog Server field. Choose the logging policy for each syslog server. Youcan configure up to 8 syslog servers.Click Save.Configuring the Discovery SettingsThe Cisco RV120W supports two types of discovery protocols: Bonjour and UPnP.Bonjour is a service advertisement and discovery protocol. Universal Plug andPlay (UPnP) is a networking protocol that allows devices to discover each otherand communicate on the network.Configuring BonjourTo configure Bonjour:STEP 1STEP 2STEP 3STEP 4Choose Administration > Discovery Settings > Discovery - Bonjour.Check the Enable box to enable Bonjour on the router. Unchecking this will disableBonjour.In the Bonjour Interface Control Table, you can see on which VLANs Bonjour isenabled. For example, Bonjour is by default enabled on the default VLAN ID 1. Thatmeans that the Cisco RV120W advertises itself to all devices connected to it onVLAN 1, and devices joining the network can connect to the Cisco RV120W. If youhave other VLANs created on your network, you can enable Bonjour on thoseVLANs too. (See Configuring Virtual LAN (VLAN) Membership, page 30 formore information.)Click Save.Cisco RV120W Administration Guide 130
Page 1 and 2:
ADMINISTRATIONGUIDECisco Small Busi
Page 4 and 5:
ContentsChapter 2: Configuring Netw
Page 6 and 7:
ContentsChapter 4: Configuring the
Page 8 and 9:
ContentsConfiguring Network Managem
Page 10 and 11:
1IntroductionThis chapter describes
Page 12 and 13:
IntroductionProduct Overview1Securi
Page 14 and 15:
IntroductionGetting to Know the Cis
Page 16 and 17:
IntroductionMounting the Cisco RV12
Page 18 and 19:
IntroductionConnecting the Equipmen
Page 20 and 21:
IntroductionConnecting the Equipmen
Page 22 and 23:
IntroductionUsing the Getting Start
Page 24 and 25:
IntroductionNavigating through the
Page 26 and 27:
IntroductionSaving Your Changes1Sav
Page 28 and 29:
2Configuring NetworkingThe networki
Page 30 and 31:
Configuring NetworkingConfiguring t
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Configuring NetworkingConfiguring R
Page 47 and 48:
Configuring NetworkingConfiguring R
Page 49 and 50:
Configuring NetworkingConfiguring P
Page 51 and 52:
Configuring NetworkingConfiguring I
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Configuring the Wireless NetworkA N
Page 63 and 64:
Configuring the Wireless NetworkUnd
Page 65 and 66:
Configuring the Wireless NetworkCon
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Configuring the FirewallCisco RV120
Page 77 and 78:
Configuring the FirewallConfiguring
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88: Configuring the FirewallConfiguring
Page 97 and 98: Configuring the FirewallFirewall Co
Page 99 and 100: Configuring the FirewallFirewall Co
Page 101 and 102: 5Configuring Virtual Private Networ
Page 103 and 104: Configuring Virtual Private Network
Page 121 and 122: 6Configuring Quality of Service (Qo
Page 123 and 124: Configuring Quality of Service (QoS
Page 125 and 126: Configuring Quality of Service (QoS
Page 127 and 128: Administering Your Cisco RV120WConf
Page 129 and 130: Administering Your Cisco RV120WUsin
Page 135 and 136: Administering Your Cisco RV120WCapt
Page 137: Administering Your Cisco RV120WConf
Page 143 and 144: Administering Your Cisco RV120WUpgr
Page 145 and 146: 8Viewing the Cisco RV120W StatusThi
Page 147 and 148: Viewing the Cisco RV120W StatusView
Page 159 and 160: AUsing Cisco QuickVPN for Windows 7
Page 161 and 162: Using Cisco QuickVPN for Windows 7,
Page 163: BWhere to Go From HereCisco provide
show all

Cisco Small Business RV 120W Wireless-N VPN Firewall ...

Create successful ePaper yourself

Delete template?

Save as template?