LED VISOR LIGHT - Code 3 Public Safety Equipment

More documents

Recommendations

Info

Introduction:The LED Visor Light is a new visor mounted light that incorperates (2) PAR36 modules. The LED based warninglight modules contain state-of-the-art high intensity LEDs. These products provide twenty six differentoperation modes including a steady-burn mode. The LED Visor Light is SAE J595 compliant and CA Title 13compliant when the proper flash pattern is selected (see table below).warning!This Product contains high intensity LED devices. To prevent eye damage, DO NOT stareinto light beam at close range.Warning!The use of this or any warning device does not insure that all drivers can or will observe or react to an emergencywarning signal. Never take the right-of-way for granted. It is your responsibility to be sure you can proceedsafely before entering an intersection, driving against traffic, responding at a high rate of speed, or walking onor around traffic lanes.The effectiveness of this warning device is highly dependent upon correct mounting and wiring. Read and followthe manufacturer’s instructions before installing or using this device. The vehicle operator should insure daily thatall features of the device operate correctly. In use, the vehicle operator should insure the projection of the warningsignal is not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or otherobstructions. This equipment is intended for use by authorized personnel only. It is the user’s responsibility tounderstand and obey all laws regarding emergency warning devices. The user should check all applicable city,state and federal laws and regulations.Code 3 , Inc., assumes no liability for any loss resulting from the use of this warning device.Proper installation is vital to the performance of this warning device and the safe operation of the emergencyvehicle. It is important to recognize that the operator of the emergency vehicle is under psychological and physiologicalstress caused by the emergency situation. The warning device should be installed in such a manner asto: A) Not reduce the output performance of the system, B) Place the controls within convenient reach of theoperator so that he can operate the system without losing eye contact with the roadway.Emergency warning devices often require high electrical voltages and/or currents. Properly protect and use cautionaround live electrical connections. Grounding or shorting of electrical connections can cause high currentarcing, which can cause personal injury and/or severe vehicle damage, including fire.PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCYWARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THEPUBLIC.Features and Specifications:5 3/8” tall x 11” wide x 1” thick --- weight = 1.4 lbsOperating Voltage: DC10V-30V, Reverse Polarity 1 ProtectedFlash Rate: 70 fpm minimumFlash Modes:pattern no. PATTERNS SYNCHRONIZE1 SINGLE FLASH 75FPM PHASE 1 YES2 SINGLE FLASH 75FPM PHASE 2 YES3 SINGLE FLASH 120FPM PHASE 1 YES4 SINGLE FLASH 120FPM PHASE 2 YES5 SINGLE FLASH 375FPM PHASE 1 YES6 SINGLE FLASH 375FPM PHASE 2 YES7 DOUBLE FLASH 75FPM PHASE 1 YES2
PATTERN NO. PATTERNS SYNCHRONIZE8 DOUBLE FLASH 75FPM PHASE 2 YES9 DOUBLE FLASH 130FPM PHASE 1 YES10 DOUBLE FLASH 130FPM PHASE 2 YES11 TRIPLE FLASH 75FPM PHASE 1 YES12 TRIPLE FLASH 75FPM PHASE 2 YES13 QUAD FLASH 75FPM PHASE 1 YES14 QUAD FLASH 75FPM PHASE 2 YES15 QUAD FLASH 150FPM PHASE 1 YES16 QUAD FLASH 150FPM PHASE 2 YES17 FIVE FLASH 150FPM PHASE 1 YES18 FIVE FLASH 150 FPM PHASE 2 YES19 QUAD FLASH 75FPM NFPA NO20 SINGLE FLASH 75FPM, T13 NO21 DOUBLE FLASH 75FPM, T13 NO22 MODUFLASH SIM. NO23 ACTION FLASH NO24 AUTORUN (RANDOM) NO25 STEADY BURN NO26 OFF NOFlashing Current Draw:Steady Burn Current Draw:Red/Amber: .85A Avg. each lamp .85A Avg. each lampBlue/White: 1.0A Avg. each lamp 1.0A Avg. each lampAvailable colors - Red, Amber or BlueInstallation:This unit is designed to be mounted on the vehicle's OEM sun visors via the adjustable attachement straps.Wiring:The LED Visor Light simply plugs into any standard 12/24VDC cigarette lighter socket. The plug has a 4 amp fuseinside.WARNING!If the product is to be used inside the vehicle, it may cause severe personal injury if not properlymounted and secured. Objects used in vehicle may become airborne during a collision or othersudden changes in vehicle speed or direction, such as braking, acceleration or turns.3
Page 1: INSTALLATION &OPERATIONMANUALLED VI
Page 5 and 6: NOTES5
Page 7 and 8: NOTES7

LED VISOR LIGHT - Code 3 Public Safety Equipment

Create successful ePaper yourself

Delete template?

Save as template?