Library for Building Automation Function Block Descriptions ... - Wago
Library for Building Automation Function Block Descriptions ... - Wago Library for Building Automation Function Block Descriptions ... - Wago
SCPT temp p (Fu_SCPT_temp_p)SCPT temp p (Fu_SCPT_temp_p)WAGO-I/O-PRO CAA Library ElementsCategory:Building AutomationName:FuSCPT_temp_pTyp: Function X Function block ProgramLibrary Name:Building_common.libApplicable to: Feldbus-Controller 750-819Input Parameter: Data type: Comment:dwSCPT_temp_p DWORD Input signal of the configuration variableof type SCPT_temp_pFeedback Value: Data type: Comment:FuSCPT_temp_p INT Output value SCPT_temp_pValue range –27317- 32766 [0.01 0 C]Graphical Display:Function Description:The function FuSCPT_temp_p is used if a configuration variable (configurationproperty) of type SNVT_temp_p is to be transferred from the LNS Plug-In PRIO(Neuron Chip) to the WAGO I/O PRO (C165). The configuration values are usuallytransferred via a retain variable of data type DWORD. To also reach the negativevalues of the variables SNVT_temp_p, a conversion of the values is thereforenecessary. The function FuSCPT_temp_p converts the input signal of the data typeDWORD into an output variable of type INT.Subject to design changes WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Tel.: 05 71 / 8 87-0 E-Mail: info@wago.comCopyright © 2009 Hansastr. 27 • D-32423 Minden Fax.: 05 71 / 8 87-169 Web:http://www.wago.com78
WAGO Kontakttechnik GmbH & Co. KGPostfach 2880 • D-32385 MindenHansastraße 27 • D-32423 MindenPhone: 05 71/8 87 – 0Telefax: 05 71/8 87 – 1 69E-Mail: info@wago.comInternet:http://www.wago.com
- Page 28 and 29: Dimmer Double Switch (FbDimmerDoubl
- Page 30 and 31: Switching Scene (FbSceneDigital)Fun
- Page 32 and 33: Dimming Scene (FbSceneAnalog)Functi
- Page 34 and 35: Linear 2 Point (Fu_Linear_2punkt)Ch
- Page 36 and 37: Linear 10 Point (Fu_Linear_10)Funct
- Page 38 and 39: Lowpass filter (FbFilter_T1)Time re
- Page 40 and 41: SendOnDelta for WORD (Fb_wSendOnDel
- Page 42 and 43: Stairwell Light without Pre-Warning
- Page 44 and 45: Stairwell Light with Pre-Warning (F
- Page 46 and 47: Function Description:The function b
- Page 48 and 49: Function Description:The function b
- Page 50 and 51: Level Switch for 1 to 5 stages (Fb_
- Page 52 and 53: Tableau for 8 buttons (fb_Tableau)T
- Page 54 and 55: Switching ON/OFF Delay (Fb_Delay)De
- Page 56 and 57: Limit monitor (Fb_Weather)Time Refe
- Page 58 and 59: Operating Time (FbOperationTime)Ope
- Page 60 and 61: Operating Time (FbOperationTime)Imp
- Page 62 and 63: Run Duration Control (FbRunDuration
- Page 64 and 65: Clock (Fb_Time)Graphical Display:Fu
- Page 66 and 67: Scheduler (FbTimeSwitch)Graphical D
- Page 68 and 69: Presence simulation (FbRandom)Funct
- Page 70 and 71: SNVT Setting (FbSetting)Function De
- Page 72 and 73: Unpack SNVT Setting (FbUnpackSettin
- Page 74 and 75: Unpack SNVT State (FbUnpackState)Un
- Page 76 and 77: SCPT Level Percent (FuSCPT_lev_perc
SCPT temp p (Fu_SCPT_temp_p)SCPT temp p (Fu_SCPT_temp_p)WAGO-I/O-PRO CAA <strong>Library</strong> ElementsCategory:<strong>Building</strong> <strong>Automation</strong>Name:FuSCPT_temp_pTyp: <strong>Function</strong> X <strong>Function</strong> block Program<strong>Library</strong> Name:<strong>Building</strong>_common.libApplicable to: Feldbus-Controller 750-819Input Parameter: Data type: Comment:dwSCPT_temp_p DWORD Input signal of the configuration variableof type SCPT_temp_pFeedback Value: Data type: Comment:FuSCPT_temp_p INT Output value SCPT_temp_pValue range –27317- 32766 [0.01 0 C]Graphical Display:<strong>Function</strong> Description:The function FuSCPT_temp_p is used if a configuration variable (configurationproperty) of type SNVT_temp_p is to be transferred from the LNS Plug-In PRIO(Neuron Chip) to the WAGO I/O PRO (C165). The configuration values are usuallytransferred via a retain variable of data type DWORD. To also reach the negativevalues of the variables SNVT_temp_p, a conversion of the values is there<strong>for</strong>enecessary. The function FuSCPT_temp_p converts the input signal of the data typeDWORD into an output variable of type INT.Subject to design changes WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Tel.: 05 71 / 8 87-0 E-Mail: info@wago.comCopyright © 2009 Hansastr. 27 • D-32423 Minden Fax.: 05 71 / 8 87-169 Web:http://www.wago.com78