Library for Building Automation Function Block Descriptions ... - Wago

More documents

Recommendations

Info

Constant light control for 0 – 10 V (FbConstantLightControl)Calibration:Light intensity:100% artificial lightrCalibration =5bAdaptation_in_Percent = 70Actual=Set point?NoActual
Constant light control for 0 – 10 V (FbConstantLightControl)The first measurement is performed in a darkened room using pure artificial light.The calibration value is determined as follows:If the light intensity in the workplace is higher than the set point lightintensity, the calibration value must be increased until the desired lightintensity is reached.If the light intensity in the workplace is lower than the set point lightintensity, the calibration value must be decreased until the desired lightintensity is reached.For safety reasons, the light intensity measured by the luxmeter should be about10 % higher than the desired set point light intensity.The second calibration measurement is required in order to determine thepercentage adaptation of the calibration value.This measurement is performed in a semi-darkened room with residual artificial light.The second measurement is performed as follows:If the light intensity in the workplace is lower than the set point lightintensity, the percentage of the adaptation must be increased until thedesired light intensity is reached.If the light intensity in the workplace is higher than the desired lightintensity, the percentage of the adaptation must be decreased until thedesired light intensity is reached.If the percentage adaptation of the calibration value is performed in a semi-darkenedroom, the lowest possible offset is achieved depending on the part of daylight orartificial light. The actual value of the light intensity can still be lower than the setpoint light intensity.Subject to design changes WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Tel.: 05 71 / 8 87-0 E-Mail: info@wago.comCopyright © 2009 Hansastr. 27 • D-32423 Minden Fax.: 05 71 / 8 87-169 Web:http://www.wago.com23
Page 1 and 2: Library forBuilding AutomationFunct
Page 3 and 4: GeneralWAGO-I/O-PRO CAA Library for
Page 5 and 6: Important commentsImportant Comment
Page 7 and 8: Fault indication function block (Fb
Page 10 and 11: Sunblind (FbSunblind)The times for
Page 12 and 13: Evaluation of a short / long key ac
Page 14 and 15: Time delayed switching ON and OFF (
Page 16 and 17: Ambient Light Control (Fb_AmbientLi
Page 18 and 19: Constant light control for 0 - 10 V
Page 20 and 21: Constant light control for 0 - 10 V
Page 24 and 25: Dimmer Single Switch (FbDimmerSingl
Page 26 and 27: Dimmer Single Switch (FbDimmerSingl
Page 28 and 29: Dimmer Double Switch (FbDimmerDoubl
Page 30 and 31: Switching Scene (FbSceneDigital)Fun
Page 32 and 33: Dimming Scene (FbSceneAnalog)Functi
Page 34 and 35: Linear 2 Point (Fu_Linear_2punkt)Ch
Page 36 and 37: Linear 10 Point (Fu_Linear_10)Funct
Page 38 and 39: Lowpass filter (FbFilter_T1)Time re
Page 40 and 41: SendOnDelta for WORD (Fb_wSendOnDel
Page 42 and 43: Stairwell Light without Pre-Warning
Page 44 and 45: Stairwell Light with Pre-Warning (F
Page 46 and 47: Function Description:The function b
Page 48 and 49: Function Description:The function b
Page 50 and 51: Level Switch for 1 to 5 stages (Fb_
Page 52 and 53: Tableau for 8 buttons (fb_Tableau)T
Page 54 and 55: Switching ON/OFF Delay (Fb_Delay)De
Page 56 and 57: Limit monitor (Fb_Weather)Time Refe
Page 58 and 59: Operating Time (FbOperationTime)Ope
Page 60 and 61: Operating Time (FbOperationTime)Imp
Page 62 and 63: Run Duration Control (FbRunDuration
Page 64 and 65: Clock (Fb_Time)Graphical Display:Fu
Page 66 and 67: Scheduler (FbTimeSwitch)Graphical D
Page 68 and 69: Presence simulation (FbRandom)Funct
Page 70 and 71: SNVT Setting (FbSetting)Function De
Page 72 and 73:
Unpack SNVT Setting (FbUnpackSettin
Page 74 and 75:
Unpack SNVT State (FbUnpackState)Un
Page 76 and 77:
SCPT Level Percent (FuSCPT_lev_perc
Page 78 and 79:
SCPT temp p (Fu_SCPT_temp_p)SCPT te
show all

Library for Building Automation Function Block Descriptions ... - Wago

Create successful ePaper yourself

Delete template?

Save as template?